Steinbach APPcontrol, Instruction Manual

10

061023_v1901

Pool cleaner components

Fig. 3:

1) Handle

2) Filter unit

3) Drive roller

4) Bearing for drivel roller

5) Drive belts

6) Side cover

7) Floating cable

8) Engine unit

9) Drive wheel

10) Propeller

11) Nozzle insert

12) Frame

13) Top cover

14) Power supply

Preparation

Place the cleaner into the water, while holding onto the hanging ring 

(Fig, 4). Once all the air has escaped from the cleaner, (the cleaner 

must be completely free of air, otherwise normal operation will be affect-

ed), it will sink to the bottom on its own.

Caution: For optimal performance, make sure that there is no more air 

in the cleaner (air bubbles stop coming out of the cleaner, and it stays 

on the pool fl oor properly).

Connecting the power source

When the cleaner is completely on the pool fl oor, take the power cable, 

roll it out fully and push the plug into the socket on the power supply. 

Then connect the cable to the socket (Please note when connecting 

cables that the plugs are in the right direction and position in relation 

to each other), and tighten the nuts on both sides. Connect the mains 

cable to the power source. The swimming pool cleaner is now ready for 

use.

Panel 

NO.

Sign

Indicate

Function

1

ON/OFF

Switch on 

or off

■ Press this button machine will be 

switched on.

■ Press this button twice machine 

will work under selected mode.

■ Press  this  button  third  time  ma-

chine will be switched off.

Mode op-

tions

Choose different mode for differ-

ent purpose.

2

Mode

Fig. 5

“ALL”mode is let machine

clean swimming pool fl oor

wall and water line together.

(once wall then once fl oor)

Fig. 6

“WALL” mode is let machine

clean swimming pool

wall only.

Fig. 7

“FLOOR” mode is let machine

clean swimming pool

fl oor only.

Fig. 8

“ALL + FLOOR” mode is let

machine clean the swimming

pool fl oor three times

then climb wall once.

Working 

duration 

option

Different working duration for 

different purpose

3

Time

Fig. 9

1H 2H 3H 

Indicate different working duration

Indicate the machine status

4

Indicator Working

status

Two or three indica-

tors on

Machine stopped

1H fl ash slowly

Machine running 

for 1 hour

2H fl ash slowly

Machine running 

for 2 hour

3H fl ash slowly

Machine running 

for 3 hour

ALL light on

Working under 

mode ALL

WALL light on

Working under 

mode WALL

FLOOR light on

Working under 

mode FLOOR

ALL + FLOOR light on

Working 

under mode ALL-

FLOOR

ALL>>WALL>>FLOOR 

fl ash in order

Manual: forward

FLOOR>>WALL>>ALL 

fl ash in order

Manual: back-

ward

3H>>2H>>1H fl ash in 

order

Manual: left turn

1H>>2H>>3H fl ash in 

order

Manual: right 

turn

All lights fl ash slowly

Auto run

fi nish

You can also control the Speedcleaner APPcontrol using the APP.

Please use the following link (A IOS): Fig 14.

Bluetooth for smart phone

(optional) (Fig. 10)

NO. Indicator

Function

1

Bluetooth status

■ disconnected

■ connected

2

Searching signal

Press to start searching Bluetooth

signal.

3

▲

Manual walking forward

4

▼

Manual walking backward

5

◄

Manual left turn

6

►

Manual right turn

7

Stop sign

Manual stop machine

8

Mode

■ Pool fl oor mode

■ Pool wall mode

■ One fl oor one wall mode

■ Three fl oor one wall mode

9

Auto play or stop

■ Auto Play: working as selected mode

■ STOP: stop working automatically

Attention: “►”&“

◄

”need to be pressed constantly

.

Care and maintenance

The cleaner turns itself off automatically after a cleaning cycle. Unplug 

the mains cable, gently pull the cable, and lift the cleaner out of the 

water using the ring on the clamp nut.

Caution:

When lifting the cleaner out of the water, you must ensure that the 

cleaner does not hit the side of the pool wall, otherwise you may dam-

age both the cleaner and the liner.

EN