background image

INSSTE2411014

16

STelPrO DeSigN iNc. | Saint-Bruno-de-montarville | Quebec  | J3V 6l7

L

imite

D

 w
arranty

 

L

imite

D

 w
arranty

L

imite

D

 w

arranty

 

L

imite

D

 w

arranty

L i m i t e D   w a r r a n t y  

L i m i t e D   w a r r a n t y

  L i m i t e D   w a r r a n t y  

L i m i t e D

Lim

it

eD

 w

ar

ra

nt

Lim

it

eD

 w

ar

ra

nt

y

 L

im

it

eD

 w

ar

ra

nt

Lim

it

eD

LimiteD warranty

This  unit  has  a  3-year  warranty.  If  at  any  time  during  this  period 

the  unit  becomes  defective,  it  must  be  returned  to  its  place  of 

purchase  with  the  invoice  copy,  or  simply  contact  our  customer 

service  department  (with  an  invoice  copy  in  hand).

 

In order for 

the warranty to be valid, the unit must have been installed 

and used according to instructions.

 

If  the  installer  or  the  user 

modifies  the  unit,  he  will  be  held  responsible  for  any  damage 

resulting  from  this  modification.  The  warranty  is  limited  to  the 

factory repair or the replacement of the unit, and does not cover the 

cost of disconnection, transport, and installation.

E-mail: contact@stelpro.com 

Web site: www.stelpro.com

Summary of Contents for STE241

















Reviews: