Stern 280200 Installation And Maintenance Manual Download

Page: 2 / 11

IndeX

technIcal data

BTM FOAM E

280250

BEhind MirrOr SOAp diSpEnSEr B

280210

BEhind MirrOr SOAp diSpEnSEr E

280200

Capacity

1 Liter \ 33.8 oz.

Power Supply liquid soap dispenser

∙

Battery box for 6xD batteries

∙

12V transformer

Power Supply foam soap dispenser

12V transformer

Soap viscosity BTM Soap dispenser B/E

100-3800 cPs

Soap viscosity BTM Foam E

up to 100 cPs

Standard discharge BTM Soap dispenser B/E

1.4cc (customizable by optional remote

control)

Standard discharge BTM Foam E

Varies according to viscosity and soap consis-

tency

Sensor range

30-100 mm +/- 10 mm /1.18-3.94” (customiz-

able by optional remote control)

TEcHNIcAL DATA

PRE-INsTALLATION INFORMATION

PAcK cONTENTs

4-5 INsTALLATION

FILLING THE sOAP TANK

REMOTE cONTROL FUNcTIONs - LIQUID sOAP DIsPENsER

BATTERIEs REPLAcEMENT

REMOTE cONTROL FUNcTIONs - FOAM sOAP DIsPENsER

10 MAINTENANcE

sPARE PARTs LIsT

12-14

TROUBLEsHOOTING

LIMITED WARRANTY

Summary of Contents for 280200












Search results

Summary of Contents for 280200

Reviews:

Related manuals for 280200

Brands by name

Popular brands

Stern 280200, Installation And Maintenance Manual

Search results

Summary of Contents for 280200

Reviews:

Related manuals for 280200

Brands by name

Popular brands