background image

10

11

maIntenance

Care and cleaning of chrome and special finishes

DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like.

Use of any prohibited cleaning or maintenance products or substances could damage the 

surface of the soap dispenser. For surface cleaning use ONLY soap and water, then wipe dry 

with a clean cloth or towel. When cleaning bathroom tiles, the soap dispenser should be 

protected from any splattering of harsh cleansers. 

Disassemble of the soap pipe from the pump

The soap pipe can be disconnected from the soap pump by a simple slide & pull action. The 

sliding ring of the quick connection fixation nipple on the pump should be pulled down. It 

releases the open end of the soap pipe which can then be easily pulled out.

Filter cleaning instructions (foam dispenser only)

This soap dispenser is provided with a foam filter. It is recommended to clean the filter 

every six (6) months. 

If the soap supply has decreased, this may be caused by the clogged filter. The filter can be 

cleaned as follows:

1. Unscrew the quick connection fitting from the top of the foam compressor and pull out 

the filter housing.

2. Remove the filter from the housing and wash it under running water.

3. Reassemble the parts.

Clean the soap tank

clean out the tank prior to refill by flushing warm water through the hoses and pump until 

clean water is released from the spout. TIP: Keeping a spare tank will enable this process to 

be completed in a speedy and hygienic manner with minimal downtime.

sPaRe PaRts lIst  

10-pACK SEnSOr KiT – LiQUid

07220317 

10-pACK SEnSOr KiT – FOAM

08008003

SOAp diSpEnSEr pUMp (LiQUid/FOAM)

07222032 

FOAM diSpEnSEr pUMp+COMprESSOr KiT

07222044

SOAp diSpEnSEr SpOUT KiT (LiQUid OnLY)

07271023 

6-pACK 1L SOAp TAnK

07100035 

6-pACK BOTTLE SUppOrT KiT

07100037 

10-pACK FOAM diSpEnSEr FiLTEr

07212015

BATTErY BOX FOr 6Xd BATTEriES (LiQUid OnLY) 

06530041 

12V TrAnSFOrMEr (EU) 

06522081 

1

2V TrAnSFOrMEr (UK) 

06522086 

12V TrAnSFOrMEr (US) 

06522080 

12V TrAnSFOrMEr (AU) 

06522085 

rEMOTE COnTrOL FOr SOAp diSpEnSEr (OpTiOnAL)

07100008

rEMOTE COnTrOL FOr FOAM diSpEnSEr (OpTiOnAL)

07100009

SOAp & WATEr rEMOTE COnTrOL (OpTiOnAL)

07100014

Summary of Contents for 280200












Reviews: