Stewart MacDonald ALL AMERICAN Assembly Instructions Manual Download

Page: 3 / 12

stewmac.com

page 3 of 12

Parts list

Resistor values are indicated by colored bands, read from left
to right. The first color in the code is usually the one painted
closest to a lead wire. When a gold or silver band is present,
it’s always one of the last colors in the code. A magnifier is
a big help in reading these codes.

parts:

i-2153 allamerican

#7365

(2)

R2, R3

Resistors (100 kΩ)

#7367

(3)

R4, R6, R14

Resistors (1.0 MΩ)

#7357

(4)

R5, R9, R11, R17

Resistors (1 kΩ)

Brown Black Black Orange Brown

Yellow Purple Black

Gold Brown

Brown Black Black Yellow Brown

Brown Black Black Brown Brown

Green

Blue

Black Black Brown

#7356 (1)

Resistor (560 Ω)

#7351 (1)

Resistor (47 Ω)

Brown Green Black Brown Brown

Brown Black Black

Red

Brown

#7362 (1)

R15

Resistor (10 kΩ)

#7358 (1)

R13

Resistor (1.5 kΩ)

#7431 (1) LED mounting bezel (5mm)

#7460 (1) DC power connector (21MM)

#1611 (1) Footswitch (3PDT, latching)

#7312 (1)

Capacitor (100 µF)

#4652 (2) Mono jacks, 1/4"

#7553 (1) Metal case with 4 screws

(1) Circuit board

(Not pictured)

100uF

#7317 (4)

C2, C4, C9, C14

(.022 µF)

#7302 (1)

Capacitor (.001 µF)

#7442 (1)

Low noise op-amp (5534 500nA)

#7484 (1)

U1.2

socket for op-amp

#7455 (3) Pots

R10

R12

R16

(100 kΩ, audio taper)

#7451 (1)

Pot

(1 kΩ, linear taper)

#7421 (3)

D3, D4, D5

Red LEDs (5mm)

#7422 (1)

White LED (5mm)

#7402 (1)

Diode (P6KE12A)

#7303 (1)

C13

Capacitor (.0033 µF)

#7313 (1)

C11

Capacitor (30 pF)

#7309 (1)

Capacitor (100 pF)

102J

K5J

100

1uF

4.7uF

#7314 (2)

C3, C15

Capacitors (1 µF)

#7316 (2)

C5, C12

Capacitors (4.7µF)

2.2uF

#7315 (1)

Capacitor (2.2 µF)

#7404 (2)

D6, D7

Rectifiers (1n4001)

#7483 (1)

Transistor (2n5458)

#7465 (1) On-Off-On mini toggle switch

#7318 (1) Ribbon cable

(1) Lead wires (12")

#7560 (4) Adhesive foam tape

#7501 (4) Control knobs

22NJ

3n3K

MMK

BF6

63-

parts:

i-2153 allamerican

#7365

(2)

R2, R3

Resistors (100 kΩ)

#7367

(3)

R4, R6, R14

Resistors (1.0 MΩ)

#7357

(4)

R5, R9, R11, R17

Resistors (1 kΩ)

Brown Black Black Orange Brown

Yellow Purple Black

Gold Brown

Brown Black Black Yellow Brown

Brown Black Black Brown Brown

Green

Blue

Black Black Brown

#7356 (1)

Resistor (560 Ω)

#7351 (1)

Resistor (47 Ω)

Brown Green Black Brown Brown

Brown Black Black

Red

Brown

#7362 (1)

R15

Resistor (10 kΩ)

#7358 (1)

R13

Resistor (1.5 kΩ)

#7431 (1) LED mounting bezel (5mm)

#7460 (1) DC power connector (21MM)

#1611 (1) Footswitch (3PDT, latching)

#7312 (1)

Capacitor (100 µF)

#4652 (2) Mono jacks, 1/4"

#7553 (1) Metal case with 4 screws

(1) Circuit board

(Not pictured)

100uF

#7317 (4)

C2, C4, C9, C14

(.022 µF)

#7302 (1)

Capacitor (.001 µF)

#7442 (1)

Low noise op-amp (5534 500nA)

#7484 (1)

U1.2

socket for op-amp

#7455 (3) Pots

R10

R12

R16

(100 kΩ, audio taper)

#7451 (1)

Pot

(1 kΩ, linear taper)

#7421 (3)

D3, D4, D5

Red LEDs (5mm)

#7422 (1)

White LED (5mm)

#7402 (1)

Diode (P6KE12A)

#7303 (1)

C13

Capacitor (.0033 µF)

#7313 (1)

C11

Capacitor (30 pF)

#7309 (1)

Capacitor (100 pF)

102J

K5J

100

1uF

4.7uF

#7314 (2)

C3, C15

Capacitors (1 µF)

#7316 (2)

C5, C12

Capacitors (4.7µF)

2.2uF

#7315 (1)

Capacitor (2.2 µF)

#7404 (2)

D6, D7

Rectifiers (1n4001)

#7483 (1)

Transistor (2n5458)

#7465 (1) On-Off-On mini toggle switch

#7318 (1) Ribbon cable

(1) Lead wires (12")

#7560 (4) Adhesive foam tape

#7501 (4) Control knobs

22NJ

3n3K

MMK

BF6

63-

Summary of Contents for ALL AMERICAN













Search results

Summary of Contents for ALL AMERICAN

Reviews:

Related manuals for ALL AMERICAN

Brands by name

Popular brands

Stewart MacDonald ALL AMERICAN, Assembly Instructions Manual

Search results

Summary of Contents for ALL AMERICAN

Reviews:

Related manuals for ALL AMERICAN

Brands by name

Popular brands