manualshive.com logo in svg

StewMac Mini-LP Guitar Kit, Assembly Instructions Manual

The StewMac Mini-LP Guitar Kit is a fantastic DIY project for guitar enthusiasts. This high-quality kit includes all the necessary components to build your own mini LP-style guitar. Ensure a smooth assembly process by following the detailed step-by-step instructions provided in the free Assembly Instructions Manual. Download it now from 88.208.23.73:8080 to get started on your custom guitar creation.

Share
Download
background image

stewmac.com

11

Adjust the pickup height   

                                                                                                                                 

Holding down the low E and high E strings at the 22nd fret, 
adjust the bass side of the pickup to 1/8" from the top of 
the pickup pole to the bottom of the low E string. Adjust 
the treble side to 1/8". 

You’re done!                                                                                                                                

Congratulations! Your guitar is ready to play. We hope this 
is the first of many that you have fun assembling and cus-
tomizing. 

Final setup

Summary of Contents for Mini-LP Guitar Kit













Reviews:

No comments

Related manuals for Mini-LP Guitar Kit

Brands by name

Popular brands

Load more brands