manualshive.com logo in svg

StewMac Mini-LP Guitar Kit, Assembly Instructions Manual

The StewMac Mini-LP Guitar Kit is a fantastic DIY project for guitar enthusiasts. This high-quality kit includes all the necessary components to build your own mini LP-style guitar. Ensure a smooth assembly process by following the detailed step-by-step instructions provided in the free Assembly Instructions Manual. Download it now from 88.208.23.73:8080 to get started on your custom guitar creation.

Share
Download
background image

stewmac.com

2

These are the tools and supplies we recommend for assembling this kit. StewMac item numbers are included where applicable.

Tools

Electric hand drill
Foam sanding block (#3701 or #3699)
Phillips screwdrivers, size #1 & 2 (#3000)
Center punch or awl (#3000)
Drill bits: 
     1/16" (#1710)
     5/64" (#1712)
10mm nut driver (#5890) or wrench (#3691)
Soldering iron (#0502)
6" StewMac Shop Rule (#4905) 
12" Precision Straightedge (#3849)

Supplies

Sandpaper: 150, 220, 320, 400, 800, 1200 grits (#5562)
Light duty 3M Scotch-Brite pad (#7445) or 0000 steel wool
ColorTone Polishing Compound, Medium (#1845)
Naphtha solvent (#0766)
Glue Brush (#4167)
Rubber gloves

Finishing supplies

ColorTone Powdered Grain Filler, ebony (#0269-E)
Wipe-On Poly (#3622)
Vintage Amber Stain (#5030)
Black Fingerboard stain (#4237)

Tools and supplies

Summary of Contents for Mini-LP Guitar Kit













Reviews:

No comments

Related manuals for Mini-LP Guitar Kit

Fender CONTEMPORARY PERFORMER BASSES Manual preview
CONTEMPORARY PERFORMER BASSES
Brand: Fender Pages: 19
Daisy Rock Bangles Signature Brochure preview
Bangles Signature
Brand: Daisy Rock Pages: 17

Brands by name

Popular brands

Load more brands