12
“
A
SSEMBLY
I
NSTRUCTIONS
”
S
TEP
11 –
Pedal Support Arm
Assembly
NOTE:
For shipping purpose,
4pcs
Bolts, Round Head
(M5xp0.8x15mm)(125)
, 1pcs
Bolt, Hex Head
M10×p1.5×70mm)
(145)
and 1pcs
Nylon Nut
(M10xp1.5)(154)
are
attached to the front of the
Right Pedal Support Arm
(18)
.
a. Remove
4pcs
Bolts, Round Head
(M5xp0.8x15mm)(125)
, 1pcs
Bolt, Hex
Head (M10×p1.5×70mm)(145)
and 1pcs
Nylon Nut (M10xp1.5)(154)
from the front
of the
Right Pedal Support Arm (18).
b.
Please place
all the above pre-attached
bolts and washers in a cleared area and
position them on the floor in front of you,
these bolts and washers are for
Step 11,
13
.
c.
On the back of the
Right Pedal Support
Arm (18)
, cut off the
tie (18A)
, and attach
the back of the
Right Pedal Support Arm
(18)
to the
Right Long Stationary
Handrail (11B)
and slightly secure with
1pcs
Bolt, Socket Head
(M10xp1.5x110mm(146)
and 1pcs
Nylon
Nut (M10xp1.5)(154)
.
NOTE:
Please do
not fully tighten
1pcs
Bolt (146)
and 1pcs
Nylon Nut (154)
for letting the following
steps to
assemble
smoothly.
d.
Attach the front of the
Right Pedal Support Arm (18)
to the
Right Pivoting Arm (15B)
and
fully tighten 1pcs
Bolt, Hex Head (M10×p1.5×70mm)(145)
and 1pcs
Nylon Nut
(M10xp1.5)(154).
NOTE: Please
“
fully tighten
”
until the inner surfaces of the
U-Shaped Bracket touch to the outer surfaces of the Bearing Housing to avoid noise.
e.
Then go back to
Step c.
to fully tighten 1pcs
Bolt, Socket Head (M10xp1.5x110mm(146)
and
1pcs
Nylon Nut (M10xp1.5)(154)
on
the middle of the
Right Long Stationary Handrail (11B)
as
the drawing shown on the left.
f.
Repeat the above same procedure for the left side.
S
TEP
12 –
Pedal & Non-Slip Pad Assembly
a. Attach
Right Pedal (76)
to the
upper pedal plate
located on the rear of the
Right Pedal Support Arm (18)
and secure
with 4pcs
Bolts, Socket Head (M8xp1.25x10mm)(134).
Then place the
Non-Slip Pad (75)
onto the
Right Pedal (76)
.
b. Repeat the above same procedure for the left side.
S
TEP
13 –
Rear Rotation Cover & Front Linkage Cover Assembly
NOTE:
For shipping purpose, 4pcs
Bolts, Round Head (M5xp0.8x15mm)(125)
are attached to
the sides of the
Right Pedal Support Arm (18)
.
a. Remove
4pcs
Bolts, Round Head (M5xp0.8x15mm)(125)
from the sides of the
Right Pedal
Support Arm (18).
b. Attach the
Right Front Linkage Cover
– Top (71)
to the
Right Front Linkage Cover
– Bottom (72)
and secure with
4pcs
Bolts, Round Head (M5xp0.8x15mm)(125).
c.
Attach the
Right Rear Rotation Cover
– Top (73)
to the
Right Rear Rotation Cover
– Bottom (74)
and secure with
