background image

16

Spacing roof hooks

A - 20 cm A +/- 20 cm

2 x A - 20 cm

2

Distance measures roof-tiles

Roof-tiles

roof covering

For each collector row two rows roof-tiles are necessary. The vertical size H1 is each taken on the top edge of 

the roof-tiles.

Initial position:

top edge

roof-tiles

Initial position

1410002 Roof-tile bracket V2 

           ..

           ..

           ..

1410005 Roof-tile bracket flat roof-tile

 

  with lead 24 mm battens

If high snow loads are to be expected, the roof-

tiles have to be mounted above the rafters (in 

other words the support must lie on the rafter / 

alternatively, a higher number of roof-tiles may be 
considered, depending on load).

Initial position:

top edge

roof-tiles

FKA 200/240/270 H

FKA 200/240/270 V

Horizontal size FKA 200 H FKA 240 H FKA 270 H
Maß 

A

88,3 cm

106 cm

119,7 cm

Vertical size 

Tolerance

FKA 200 H

+ / - 10 cm

FKA 240 H

+ / - 10 cm

FKA 270 H

+ / - 10 cm

Maß 

H

77 cm

77 cm

77 cm

Horizontal size FKA 200 V FKA 240 V FKA 270 V
Maß 

A

122 cm

122 cm

122 cm

Vertical size 

Tolerance

FKA 200 V

+ / - 10 cm

FKA 240 V

+ / - 10 cm

FKA 270 V

+ / - 10 cm

Maß 

H 1

60 cm

60 cm

80 cm

Maß 

H 2

77 cm

77 cm

77 cm

Summary of Contents for FKA 200H









































Reviews: