EN
GL
ISH
qqqĪZ`.<é<`VHCĪHB
`&VHC
Ĝŗ
.CZ`<<`.HC
Z%`t
.CZ`<<`.HC
3. Safety
Only qualified contractors should carry out installation, commis-
sioning, maintenance and repair of the module.
4. Equipment
description
4.1 Required
accessories
Your photovoltaics dealer can advise you on which accessories are
suitable for your module. You require the following accessories
for commissioning the module.
- Frame
- Inverter
- Supply meter
- DC disconnect switch
5. Preparations
5.1 Installation
location
DANGER Fire
Never install the module near flammable gases or va-
pours; the module may generate sparks.
Choose an installation location with maximum sunlight all year
round. Avoid areas in shadow.
In northerly climes, position the system so that it faces south. De-
termine the optimum adjustment angle depending on the latitude
of the installation location. Ask your photovoltaics dealer for this
information.
5.2 Handling
Damage to the appliance and environment
Never transport the modules without securing them or
leave them unsecured. Otherwise damage such as glass
breakage may occur.
6. Mounting
Depending on the frame configuration, the modules can be se-
cured with screws or clamped. The installation frame must be
made of a strong, corrosion and weather-resistant material.
6.1
Securing the module to the frame with screws
2
6
_4
3_0
1_0
0
0
4
f
Lay the module on the frame.
f
Insert four stainless steel screws (M8) through the holes in
the frame (see "Specification"/"Dimensions").
f
Secure screws to frame, in each case using 2 stainless steel
washers, a stainless steel spring washer or serrated washer
and stainless steel nut (M8).
6.2
Clamping the module to the frame
The modules may only be clamped to the long and short frame sides
in the permitted clamping area (see "Specification"/"Dimensions").
When using the clamping method, for safety reasons apply an
anti-slip facility that is secured with screws to the lowest row of
modules.
Note
f
Also observe the installation instructions for the
frame system in this connection.
The clamping brackets must not protrude from the module frame
to the glass side.
2
6
_4
3_0
1_0
0
1
0
1
2
1 Module frame
2 Clamping bracket
f
Lay the module on the frame.
f
Clamp the module with the clamping bracket.
Summary of Contents for 273275
