background image

EN - 7

 6.1.3  Cutting height adjustment

Adjust the cutting height as indicated in (par. 5.7).

 6.1.4  Adjusting the handle height

  Do this when the cutting means is stationary.

The handle height can be adjusted to 3 different 

positions, as marked on the handle base (Fig.16.A).

To change the handle height, pull both levers on the handle 

sides (Fig.16.B) (Type “I”- “II”), and hold them in position.

Move the handle carefully to the desired 

height and release the two levers.

It is also possible to fold the handle to the 

closed position from the working position.

 6.2  SAFETY CHECKS

Run the following safety checks and check that the 

results correspond to those outlined on the tables.

  Always carry out the safety checks before use.

 6.2.1 

General safety check

Object

Result

Grips

Clean, dry.

Handle

Fixed firmly to the machine.

Cutting means

Clean, not damaged 

or worn.

Rear discharge guard; 

grass catcher

Good condition. No 

damage. Properly installed.

Side discharge guard, 

side discharge chute

Good condition. No 

damage. Properly installed.

Engine brake lever 

/ cutting means

The lever must move 

freely, it must not need 

forcing and should 

return automatically 

and rapidly back to 

the neutral position.

Starter cable

The cable must be intact.

Screws/nuts on the 

machine and on the 

cutting means

Correctly tightened 

(not loose).

Electric cables and 

spark plug cable

Intact to prevent sparks 

from occurring

Spark plug cap

Intact and correctly fitted 

on the spark plug.

Machine

No signs of damage 

or wear.

 6.2.2  Machine operating test

Action

Result

1. 

Start the machine 

(par. 6.3).

2. 

Release the engine 

/ cutting means 

brake lever.

1. 

The cutting means 

should move.

2. 

The levers should 

return automatically 

and rapidly to the 

neutral position, the 

engine must switch 

off and the cutting 

means must stop 

within a few seconds.

1. 

Start the machine 

(par. 6.3).

2. 

Engage the 

drive lever.

3. 

Disengage the 

drive lever.

2. 

The wheels 

should move the 

machine forward.

3. 

The wheels should 

stop and the machine 

stops moving forward.

Test driving

No abnormal vibrations.

No abnormal sound.

  If any of the results fail to match the indications 

provided in the tables, do not use the machine! Contact 

a service centre to have it checked and repaired if ne

-

cessary.

 6.3 

START-UP

NOTE

 Start up the machine on a flat 

surface without obstacles or high grass.

 6.3.1  Manual starter handgrip models

1.

For cold starts:

 move the throttle to the “Choke” 

engaged position (Fig.6.A) (if present).

2.

Pull the engine cutting means brake 

lever towards the handle (Fig.17.A).

NOTE

 Keep pulling the engine / cutting 

means brake or the engine will stop.

3.

Grab hold of the starter handgrip and tug the 

starter cable firmly to start the engine (Fig.17.B).

4.

When the engine has started, shift the 

throttle to the full speed position (if fitted).

NOTE

 Using the choke when the engine 

is already warm can foul the spark plugs and 

cause the engine to run erratically.

Summary of Contents for MP2 504 Series




































Reviews: