EN - 24
A continuous buzzer indicates
when the grass catcher is full:
Proceed as follows:
1.
Disengage the cutting means
(par.13.B)
and the audible signal will stop;
2.
Stop the machine.
a.
For models type “I” and “II”:
3.
Extract the lever (fig. 21.A - if available)
or grasp the rear handle (fig. 21.A1) and
overturn the grass catcher to empty it.
4.
Move the machine about 1 m.
5.
Close the grass catcher again so that it
remains coupled to the pawl (fig. 21.B).
b.
For models type “III”:
3.
Press the grass catcher opening button (fig.
13.U) for about 1 s to open it completely
and empty it; alternatively, the grass
catcher opening button can be held down
until the opening required for emptying is
reached. When the button is released, the
bag will remain in the position reached.
4.
Move the machine about 1 m.
5.
Press and hold the grass catcher closing
button (fig. 13.V) to close it completely.
NOTE
If the key is fully inserted (fig.12.A), pressing
the reverse button (fig.13.C) together with the
opening (fig.13U) or closing (fig.13V) buttons
is possible open or close the grass catcher
even when the driver is not sitting on board.
7.5.5 Cleaning the discharge chute (
for
rear collection models only)
Cutting very tall or wet grass, particularly
at excessively high speed, can clog up
the discharge chute. If it clogs, follow the
instructions provided in par. 8.4.2.
7.5.6 Mowing completed
When mowing has been completed:
1.
disengage the cutting means;
2.
turn around with the cutting means
assembly in its highest position. (par. 6.4)
7.6 STOP
To stop the machine:
1.
Release the drive pedal to stop the drive gear.
2.
Turn off the machine by removing the key.
NOTE
To save battery power, do not leave the key in the
"run" position when the machine is not in use.
7.7 AFTER USE
1.
Allow the machine to cool before
storing it in an enclosed space.
2.
Clean (par. 8.4).
3.
Make sure there are no loose or
damaged components. If necessary,
replace the damaged components and
tighten any screws and loose bolts or
contact the authorised service centre.
4.
Position the machine near to a power socket
and charge the battery *(par. 8.2.2) so that
it is ready to be used when next required.
whenever the machine is left
unattended, the operator leaves the
driving seat or parks the machine:
1.
Stop the machine;
2.
bring the cutting means assembly
to the lowest height position (1)
3.
make sure that all moving parts
have come to a complete stop;
4.
remove the ignition key;
ATTENTION
Always leave the machine in a shaded
area or sheltered environment at a
temperature below +35 °C
8. ROUTINE MAINTENANCE
8.1 GENERAL INFORMATION
DANGER
The safety regulations to follow are described
in chap. 2. Strictly comply with these
instructions to avoid serious risks or hazards.
Before commencing any inspections, cleaning
or maintenance/adjustments on the machine:
1.
disengage the cutting means;
2.
stop the machine;
Summary of Contents for MPST 84 Li 48 V1
