background image

DO  NOT  OPEN  THE  TABLE  TO  PLAYING  POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE  STANDING  UNATTENDED.  IT  COULD  BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.

AT  LEAST  TWO  (2)  ADULTS  ARE  NEEDED  TO
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING  TOPS  TO  BASE,  HANDLE  TOP
ASSEMBLIES  BY  GRASPING  ONLY  THE  TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, U-
SUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN  MOVE  AND  COULD  PINCH  FINGERS  OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS  SHOWN  WITH  LEGS  FULLY  CLOSED  AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN

Y TO ASSEMBLE. TABLE TOPS ARE

LEGS AND TR
HEAVY -
ALONE!

DO  NOT  ATTEMPT  TO  ASSEMBLE

TUBES UP

Table Top
Assembly

21

U-Support

17

Strut Tube

7

7

With at least 2 adults, 
slide Table Top Assembly 
onto Strut Tubes (#17).

17

Strut Tube

PIVOT STRUT

Figure  4

5

7.

Attach Table Top Assembly to Base Assembly as shown in 

Figure 4

.  Pivot Strut Tubes (#17) up as shown; then, with 

at least one adult on each side of Table Top, lift top and 

align ends of U-support tube (#21) with tops of Strut 

Tubes (#17) on Caster Beams (#7) as shown in 

Figure 4

.  

Slide tubes together.

Summary of Contents for Play The Best T8780Q











Reviews: