11
This machine is fitted with a “Tap & Go” head.
To release more line, tap the cutting line head
against the ground with the engine at top speed:
the line will be released automatically and the
knife will cut off the excess length.
4.3.4 Saw blade (if permitted) (Fig. 18)
WARNING!
When using the saw blade,
where permitted, the specific guard must al-
ways be fitted. The blade must always be well
sharpened to reduce the risk of kickback.
WARNING!
When felling small trees, es-
timate the direction in which the cut tree will
fall, also taking the wind direction into con
-
sideration.
To get a good result when felling small trees,
the cut must be made with a rapid movement to
-
wards the branch or trunk to be cut, with the en
-
gine at maximum revs.
Do not use the right-hand area of the blade be-
cause there is a high risk of kickback or the blade
seizing up, due to the direction of rotation.
4.4 WHEN WORK IS FINISHED
When you have finished your work:
– Stop the machine as indicated previously (see
3.3).
– Wait for the cutting device to stop and then
mount the blade guard.
5. ROUTINE MAINTENANCE
Correct maintenance is essential to maintain
the original efficiency and safety of the machine
over time.
WARNING!
During maintenance opera-
tions:
– Remove the spark plug cap.
– Wait until the engine is sufficiently cold.
– Use protective gloves when handling the
blades.
– Keep the blade protection device on, ex
-
cept when intervening directly on the blade.
– Never dispose of oils, fuel or other pollut-
ing materials in unauthorised places.
5.1 STORAGE
At the end of each working session, carefully
clean the machine of dust and debris, and make
sure that there are no damaged parts, replacing
any faulty parts. The machine must be stored in
a dry place away from the elements and with the
cover correctly fitted.
5.2 CLEANING THE ENGINE
AND THE SILENCER
To reduce fire risks, periodically clean the cylin
-
der fins with compressed air and clear the silenc
-
er area to get rid of sawdust, branches, leaves or
other debris.
5.3 STARTING UNIT
To avoid overheating and damage to the engine,
always keep the cooling air vents clean and free
of sawdust and debris.
If you notice signs of wear on the starter cable,
contact your Dealer for a replacement.
5.4 NUTS AND SCREWS
Periodically check that all the nuts and screws
are securely tightened and the handgrips are
tightly fastened.
5.5 CLEANING THE AIR FILTER (Fig. 19)
IMPORTANT
Cleaning the air filter is essential to
guarantee the efficiency and duration of the ma
-
chine. Do not work with a damaged filter or with-
out a filter, as this could permanently damage the
engine.
It must be cleaned after every 15 working hours.
Clean the filter as follows:
– Loosen the knob (3), remove the cover (1) and
the filter element (2).
– Wash the filter element (2) with soap and wa
-
ter. Do not use petrol or other solvents.
– Leave the filter to dry in the open air.
– Fit the filter element (2) and the cover (1) back
on, tightening the knob (3) again.
5.6 CHECKING THE SPARK PLUG ( (Fig. 20)
Periodically remove and clean the spark plug us
-
ing a metal brush to get rid of any deposits.
Check and reset the correct distance between
the electrodes.
Replace the spark plug and fasten it firmly using
the supplied wrench.
Summary of Contents for SBC 627 K
