0478 909 9928 A - EN
6
●
Following installation of a new mowing
blade, confirm the blade replacement in
the "Service" menu (see instruction
manual for the robotic mower).
3.3 Removing ALM 030
Removing the mowing blade
●
Push in both tabs (1) on the
blade support with one hand and
hold. Remove fastening nut (C) with
your other hand. Remove the mowing
blade together with the fastening nut.
Removing the blade support
●
Insert puller (2) into the blade support
as shown and turn anti-clockwise to the
stop.
●
Support the machine with one hand,
remove blade support (B) by pulling on
puller (2).
4.
1
Adapting the programming
The robotic mower mows the mowing area
automatically as usual when the mowing
blade ALM 030 is fitted.
The bigger cutting width enables the
mowing duration
to be reduced by up to
10% – see the section "Adapting the
programming" in the instruction manual for
the robotic mower.
5.
1
Maintenance operations
●
Weekly
Carry out a weekly visual
inspection of the mowing blade, blade
support and fastening nut for damage
(notches, cracks, fractures, etc.) and
wear.
●
Replace the mowing blade every
200
hours
.
Replacement blade (30 cm):
6309 702 0
1
02
5.2 Cleaning
●
Clean the mowing blade
weekly
(e.g. with a brush). If the noise
produced by the machine increases
during mowing, remove any dirt from
the mowing blade, blade support and
mowing deck housing more frequently.
The mowing blade and blade support
can also be installed offset by 180°.
5.3 Mowing blade maintenance
●
Maintain the mowing blade as per the
instruction manual for the robotic
mower.
●
For information on removing and
installing the mowing blade, see the
sections "Removing ALM 030" (
and "Installing ALM 030". (
The following technical data of the robotic
mower changes when the accessory
ALM 030
is fitted:
4. Notes on mowing
6
7
5. Maintenance
Risk of injury!
In particular, check for
wear
on the
mowing blade; the same wear limits
apply as for the original mowing
blade.
The
mowing blade
,
blade support
and
fastening nut
must be
replaced if damaged (e.g. broken,
worn).
6. Technical specifications
Cutting width
30 cm
Sound emissions:
In accordance with Directive 2006/42/EC
and the EN 50636-2-107 standard:
Measured sound
power level L
WA
64 dB(A)
Uncertainty K
WA
3 dB(A)
L
WA
+ K
WA
67 dB(A)
Sound pressure level
L
pA
53 dB(A)
Uncertainty K
pA
3 dB(A)
Summary of Contents for ALM 030
