Stihl FR 235 Instruction Manual Download

Page: 13 / 24

► Rotate the mowing head (1) counterclockwise

until the stop pin (4) engages in position.

The shaft is now blocked.

► Tighten down the mowing head (1) firmly by

hand.

► Remove the stop pin (4).
6.8.2

Removing the Mowing Head

► Shut off the engine.

► Insert the stop pin in the bore as far as stop

and hold it depressed.

► Rotate the mowing head until the stop pin

engages in position.

The shaft is now blocked.

► Unscrew the mowing head clockwise.

► Remove the thrust plate.

► Remove stop pin.

6.9

Removing and Installing Metal

Cutting Attachment

6.9.1

Mounting the Metal Cutting Attach‐

ment

► Shut off the engine.

0000-GXX-3032-A1

5
6

► Place the thrust plate (5) on the shaft (6) so

that its smaller diameter faces up.

► Place the metal cutting attachment (4) on the

thrust plate (5). If you are fitting a grass cutting

blade with more than 4 cutting edges: Its cut‐

ting edges must face in the same direction as

the arrow on the deflector.

► Place the thrust washer (3) on the metal cut‐

ting attachment (4) so that its raised side faces

up.

► Place the rider plate (2) on the thrust washer

(3) so that its closed side faces up.

► Insert the stop pin (7) in the bore as far as

stop and hold it depressed.

► Rotate the metal cutting attachment (4) coun‐

terclockwise until the stop pin (7) engages in

position.

The shaft (6) is now blocked.

► Fit the nut (1) counterclockwise and tighten it

down firmly.

► Remove the stop pin (7).
6.9.2

Removing the metal cutting attach‐

ment

► Shut off the engine.

► Insert the stop pin in the bore up to the limit

stop and hold it depressed.

► Rotate the metal cutting attachment clockwise

until the stop pin engages in position.

The shaft is now blocked.

► Unscrew the mounting nut clockwise.

► Remove the fastening parts, metal cutting tool

and pressure plate.

► Remove the stop pin.

Adjusting Trimmer for User

7.1

Fitting and Adjusting the Carry‐

ing System

► Put the carrying system on your back.

0000-GXX-7843-A0

► Close buckle (1) on the waist belt.

0000-GXX-7844-A0

► Tighten the straps until the waist belt fits

snugly on your hips and the back padding is

against your back.

► Thread the end of the waist belt through the

loop (2).

7 Adjusting Trimmer for User

English

0458-527-0121-B

Summary of Contents for FR 235

























Search results

Summary of Contents for FR 235

Reviews:

Related manuals for FR 235

Brands by name

Popular brands

Stihl FR 235, Instruction Manual

Search results

Summary of Contents for FR 235

Reviews:

Related manuals for FR 235

Brands by name

Popular brands