Stihl MS 400 C-M Instruction Manual Download

Page: 22 / 32

► With outstretched arms, cut through the stabi‐

lizing strap horizontally from outside at the

same level as the felling cut.

The tree falls.

11.8.8

Felling normal, large diameter tree

A normal tree is felled with a felling cut and stabi‐

lizing strap. This felling cut must be performed if

the tree diameter is greater than the guide bar’s

length.

► Shout a warning.

0000-GXX-1256-A0

► Apply the spiked bumper at the same height

as the felling cut and use it as a pivot.

► Hold the saw horizontally and swing it into the

felling cut as far as possible.

► Enlarge felling cut in direction of hinge.

► Enlarge felling cut in direction of stabilizing

strap.

► Move to the other side of the tree.

► Plunge the guide bar into the felling cut at the

same height.

► Enlarge felling cut in direction of hinge.

► Enlarge felling cut in direction of stabilizing

strap.

0000-GXX-1257-A0

► Insert a felling wedge. The felling wedge must

match the tree diameter and the width of the

felling cut.

► Shout a warning.

► With outstretched arms, cut through the stabi‐

lizing strap horizontally from outside at the

same level as the felling cut.

The tree falls.

11.8.9

Felling a small diameter leaner

A leaner is felled with a felling cut and holding

strap. This felling cut must be performed if the

tree diameter is less than the guide bar’s length.

► Shout a warning.

0000-GXX-1258-A0

► Plunge the guide bar into the felling cut until it

is visible at the other side of the trunk,

11.8.5.

► Enlarge felling cut in direction of hinge.

► Enlarge felling cut in direction of holding strap.

0000-GXX-1259-A0

► Shout a warning.

► With arms outstretched, cut through the hold‐

ing strap from outside at a downward angle.

The tree falls.

11.8.10 Felling a large diameter leaner
A leaner is felled with a felling cut and holding

strap. This felling cut must be performed if the

tree diameter is greater than the guide bar’s

length.

► Shout a warning.

0000-GXX-1260-A0

► Apply the spiked bumper behind the holding

strap at the same height as the felling cut and

use it as a pivot.

► Hold the saw horizontally and swing it into the

felling cut as far as possible.

English

11 Operating the Saw

0458-788-0121-B

Summary of Contents for MS 400 C-M

































Search results

Summary of Contents for MS 400 C-M

Reviews:

Related manuals for MS 400 C-M

Brands by name

Popular brands

Stihl MS 400 C-M, Instruction Manual

Search results

Summary of Contents for MS 400 C-M

Reviews:

Related manuals for MS 400 C-M

Brands by name

Popular brands