Stihl MS 400 C-M Instruction Manual Download

Page: 16 / 32

10 Checking the Saw

10.1

Checking the Chain Sprocket

► Shut off the engine.

► Disengage the chain brake.

► Remove the chain sprocket cover.

► Remove the bar and chain.

0000-GXX-3162-A0

► Use a STIHL gauge to check the wear marks

on the sprocket.

► If wear marks are deeper than a = 0.5 mm: Do

not use your chainsaw and contact your

STIHL servicing dealer for assistance.

The chain sprocket must be replaced.

10.2

Checking the Guide Bar

► Shut off the engine and engage the chain

brake.

► Remove the chain and guide bar.

0000-GXX-1217-A0

► Measure depth of bar groove with scale on

STIHL filing gauge.

► Install a new guide bar if one of the following

points applies:

–

Guide bar is damaged.

–

Measured bar groove depth is less than

specified minimum depth, 19.3.

–

Bar groove is pinched or splayed.

► If you have any queries: Contact your STIHL

servicing dealer for assistance.

10.3

Checking the Saw Chain

► Shut off the engine and engage the chain

brake.

0000-GXX-1218-A0

► Use a STIHL filing gauge (2) to check the

height of the depth gauges (1). The STIHL fil‐

ing gauge must match the chain pitch.

► If a depth gauge (1) projects from the filing

gauge (2): Lower the depth gauge (1), 16.3.

0000-GXX-1372-A0

► Make sure the service marks (1 to 4) on the

cutters are visible.

► If one of the service marks is not visible on a

cutter: Do not use your chainsaw and contact

your STIHL servicing dealer for assistance.

► Use a STIHL filing gauge to check that a filing

angle of 30° has been maintained on all cut‐

ters. The STIHL filing gauge must match the

chain pitch.

► If a filing angle of 30° has not been main‐

tained: Resharpen the saw chain.

► If you have any queries: Contact your STIHL

servicing dealer for assistance.

10.4

Testing the Chain Brake

► Shut off the engine and engage the chain

brake.

WARNING

■ The chain's cutters are very sharp. There is a

risk of cut injuries.

► Wear work gloves made of durable mate‐

rial.

► Try to pull the chain along the guide bar by

hand.

If the chain cannot be pulled along the bar by

hand, the chain brake is functioning.

English

10 Checking the Saw

0458-788-0121-B

Summary of Contents for MS 400 C-M

































Search results

Summary of Contents for MS 400 C-M

Reviews:

Related manuals for MS 400 C-M

Brands by name

Popular brands

Stihl MS 400 C-M, Instruction Manual

Search results

Summary of Contents for MS 400 C-M

Reviews:

Related manuals for MS 400 C-M

Brands by name

Popular brands