background image

With continued use, the last quantity of water set

will be fed to the abrasive wheel again automati‐

cally.
If the engine is stopped and restarted, the elec‐

tronic water control is switched off.
7.3.1

For installation on the STIHL FW 20

cut-off machine cart

If the cut-off machine is mounted on the STIHL

FW 20 cut-off machine cart in combination with

the water tank, feed the maximum amount of

water.

7.4

Maintenance and care

If too little water or no water is fed to the abrasive

wheel during use although the electronic water

control has been activated:

2

370BA086 KN

1

► Remove the coupling sleeve (1)

► Unscrew "water connection with screen" (2)

and rinse under running water – the screen

remains on the water connection

If too little water or no water is fed to the abrasive

wheel although the screen has been cleaned,

visit your servicing dealer.

8

Assembling the cast arm

and guard

The "cast arm with guard" is mounted on the

inboard side by the manufacturer.
The "cast arm with guard" can also be mounted

on the outboard side depending on require‐

ments.
Assembly on the inboard side is recommended

for freehand cutting on account of the better bal‐

ance.

8.1

Outboard mounting

► Disassemble the abrasive wheel (see “Fitting /

replacing an abrasive wheel”)

8.1.1

Removing the water attachment

3

2

1

1

1307BA002 KN

► Unscrew the banjo bolt (1) with the combina‐

tion wrench – in the process, remove the

square nut from the inside of the guard from

the guide

► Remove the water hose (2) with connector

from the adjusting lever (3)

► Pull the water hose (2) out of the

guide (arrows) in the V-belt guard

8.1.2

Removing the adjusting lever

2

370BA069 KN

1

3

► Unscrew the banjo bolt (1) with the combina‐

tion wrench and remove it together with the

seal – in the process, remove the square nut

from the inside of the guard from the guide

► Unscrew the screw (2)

► Turn the adjusting lever (3) upwards and

remove

8.1.3

Slackening the V-belt

1

1

1

2

0

1307BA003 KN

► Unscrew the nuts (1) – do not remove them

8 Assembling the cast arm and guard

English

0458-753-8321-C

17

Summary of Contents for TS 480i





































Reviews: