Stockmaster Mezzalad, Assembly Instructions

Mezzalad Assembly

Mezzalad Assembly

IMPORTANT

: 

To avoid assembly problems follow these instructions exactly. 

Step 1 

- 

At the top of the ladder, Fix the Upper Handrail to the Ladder Stile at A & B using the 6 x 40mm bolts nuts 

and washers - 

Finger tight only.

 (See illustration No. 1)

Note: 

Bolt Heads should be seen from this face

Step 2

 - 

At the centre of the ladder, fix the lower end of the Upper Handrail to the Ladder Stile at C & the upper end of 

the Lower Handrail to the Ladder Stile at D. Use the 6 x 40mm bolts nuts and washers - 

Finger tight only.

 (See illustration 

No. 2)

Step 3

 - 

At the base of the ladder, fix the lower end of the Lower Handrail to the Ladder Stile at E & F using the

6 x 40mm bolts nuts and washers. 

NOW tighten all bolts

.

(See illustration No. 3)

Step 4 

-

 Assemble the Tube of the Safety Gate to the Gate Hinge/Latch. Locate the end of the Tube with the hole in 

it. Seat this end into the Gate Hinge/Latch and Insert a Clevis Pin into the hole. (See illustration No. 4)

Step 5

 -

 Push the Clevis Pin thru the Tube and Gate/Latch, fit the Washer and secure with the R Clip.

(See illustration 

No. 5)

Step 6 

-

 Fit the Safety Gate to the top of the Handrail. It may be mounted to either the left or right side. Use a Clevis 

Pin, R Clip and Washer to secure. (See illustration No. 6)

Step 7 

-

 Fit the remaining Gate Hinge/Latch to the top of the opposite Handrail. Place the Nylon Washer

between the Handrail and Gate Hinge/Latch and pass the bolt thru the assembly. Fit the Washer and Nut - 

Finger tight 

only.

 (See illustration No. 7)

Step 8

 -

 Lower the Safety Gate into the Latch (See illustration No. 8)

Step 9 

-

 Tighten the Gate Latch bolt. (See illustration No. 9)

Step 10 

- 

Ensure that a clear space of 770mm is available at the Mezzalad mounting position. Lay the Mezzalad 

against the Upper floor and adjust the position so that the top step is flush with the Upper floor. Position the Mezzalad 
in the centre of the opening. (See illustration No. 10)

Step 11

 - 

Carefully ascend the ladder and engage mounting bracket into the slot at the left hand side of the

Mezzalad. (See illustration No. 11)

Note: 

Illustration No. 11 shows a floor mounting application. For a wall mounting application place this bracket on 

the right hand side

.

Step 12

 - 

Position the Bracket Tab against the wall for a floor mounting, or floor for a wall mounting application. 

Fasten the bracket to the floor or wall using appropriate fasteners (not supplied). One 10mm diameter hole and 2 x 
5mm diameter holes are providedin each bracket. (See illustration No. 12)

Step 13 

-

 Engage the remaining bracket into the slot on the opposite side of the Mezzalad. Repeat the

instructions above in step 12 and fasten the bracket. Pull the ladder out fully to the using (open) position and check that 
the upper surface of the top step is flush with the upper floor. Also check that the Bracket Tabs are flush with the floor 
or wall (dependant on chosen mounting position). 

Thank you for choosing Stockmaster. Your safety is in 

good hands. Please register your 2 year warranty online at

www.stockmaster.co

2 YEAR WARRANTY

This completes the product assembly

Before use - See product Risk Assesment at

www.stockmaster.co

RISK ASSESMENT