background image

13

1. With a clean, dry towel, wipe excess lubricant from the

spigot assembly and o-ring. Firmly grasp the spigot
assembly with both hands and squeeze the o-ring
upward (Fig 16). When a loop is formed, roll the o-ring
out of the groove toward the end of the spigot assembly.
(See Fig. 17 for a cutaway view of the spigot assembly.)

CAUTION

Do not use any type of sharp object to remove O-rings.
Sharp objects may damage spigot bodies.

2. Place all loose parts in a pan or container and take

them to the wash sink, filled with warm, soapy water, for
cleaning.

3. Wash the product outlet with warm soapy water

using the brush provided.

G. For removal and disassembly of the divider plate

and agitator assembly, refer to the following steps:

WARNING

Hazardous Voltage

The stirring Only-Off-Stirring & Freezing switch must be
placed in the OFF position when disassembling for
cleaning or servicing. The freezer must be disconnected
from electrical supply before removing any access pan-
els. Only a qualified service technician may remove
access panels. Failure to disconnect power before servic-
ing could result in death or serious injury.

2. Remove the sealer ring by squeezing the looped

section and lifting out of the product cylinder (Fig. 19).

Figure 18

Removing Drive Cap and O-Ring

3. To remove the divider plate and agitator assembly, the

divider plate must be first rotated counterclockwise to
unlock and lift out of the product cylinder.

4. Once the divider plate and agitator assembly are

lifted off the vertical product cylinder center post and
out of the product cylinder, remove the divider plate
assembly and anti-lift disc. Remove the plastic
agitator bushing from the bottom of the product
cylinder center post by lifting up and out of the
product cylinder (Fig. 20). - Refer to Figure 23 for an
exploded view.

Figure 19

Removing Sealer Ring

Figure 20

Removing Agitator Assembly and Lower Bushing

1. Remove the drive cap and o-ring from the agitator

tube (Fig.18).

Summary of Contents for 100CA






























Reviews: