StoneAge AUTOSTROKE AST-200-V2 User Manual Download

Page: 3 / 28

866-795-1586 • WWW.STONEAGETOOLS.COM

DESCRIPTION OF EQUIPMENT AND
INTENDED USE

The AutoStroke (AST-200-V2) is an accessory for the Autobox

ABX-

2L, ABX-2L-V2, ABX-3L, and ABX-3L-V2, that can be mounted to
both Autobox

Control Boxes. The AutoStroke detects when the

lance encounters a blockage in a tube and retracts the lance for a
set time before continuing forward again, allowing the banshee to
continue to rotate and reducing potential hose damage.

KEY FEATURES:

•

Air motor generator allows operation with compressed air as

opposed to batteries.

•

Automatically retracts lance when blockage is encountered.

•

Adjustable hose push force.

•

Adjustable retract time.

•

Switch allows disabling functionality when not desired.

•

Mounts on CB stand and connects in line with Autobox

ABX-

2L, ABX-2L-V2, ABX-3L, and ABX-3L-V2L forward, reverse,
and clamp, airlines with two additional signal lines from the ABX
unit.

SPECIFICATIONS

AutoStroke (AST-200-V2)

Weight:

18 lbs

(8.2 kg)

AutoStroke (AST-200-V2)

Dimensions:

16.9” Long x 11.7” Tall x 7.9” Wide

(429 mm x 297mm x 201mm)

Air Pressure:

40 to 125 psi

(2.8 to 8.6 bar)

Air Consumption:

3 CFM

(5 m³/hr)

StoneAge Inc.
466 S. Skylane Drive
Durango, CO 81303, USA
Phone: 970-259-2869
Toll Free: 866-795-1586
www.stoneagetools.com

StoneAge Europe
Unit 2, Britannia Business Centre
Britannia Way
Malvern WR14 1GZ
United Kingdom
Phone: +44 (0) 1684 892065

This manual must be used in accordance with all applicable national laws. The manual shall be regarded as a part of the machine

and shall be kept for reference until the final dismantling of the machine, as defined by applicable national law(s).

Updated manuals can be downloaded at:

https://www.stoneagetools.com/manuals

MANUFACTURER’S INFORMATION

Summary of Contents for AUTOSTROKE AST-200-V2




























Search results

Summary of Contents for AUTOSTROKE AST-200-V2

Reviews:

Related manuals for AUTOSTROKE AST-200-V2

Brands by name

Popular brands

StoneAge AUTOSTROKE AST-200-V2, User Manual

Search results

Summary of Contents for AUTOSTROKE AST-200-V2

Reviews:

Related manuals for AUTOSTROKE AST-200-V2

Brands by name

Popular brands