background image

16

866-795-1586 • WWW.SEWERNOZZLES.COM

TERMS AND CONDITIONS AND WARRANTY INFORMATION

1. 

 Acceptance of Terms and Conditions.

  Receipt of these 

Terms and Conditions of Sale (“Terms and Conditions”) shall 

operate as the acceptance by StoneAge, Inc. (“Seller”) of the 
order submitted by the purchaser (“Buyer”).  Such acceptance 

is made expressly conditional on assent by Buyer to these 

Terms and Conditions.  Such assent shall be deemed to have 

been given unless written notice of objection to any of these 

Terms and Conditions (including inconsistencies between 

Buyer’s purchase order and this acceptance) is given by Buyer 
to Seller promptly on receipt hereof.  

Seller desires to provide Buyer with prompt and efficient 
service.  However, to individually negotiate the terms of each 
sales contract would substantially impair Seller’s ability to 
provide such service.  Accordingly, the product(s) furnished 
by Seller are sold only according to the terms and conditions 
stated herein and with the terms and conditions stated in any 

effective StoneAge Dealer Agreement or StoneAge Reseller 
Agreement, if applicable.  Notwithstanding any terms and 
conditions on Buyer’s order, Seller’s performance of any 
contract is expressly made conditional on Buyer’s agreement 

to these Terms and Conditions unless otherwise specifically 

agreed to in writing by Seller.  In the absence of such 
agreement, commencement of performance, shipment and/
or delivery shall be for Buyer’s convenience only and shall not 

be deemed or construed to be an acceptance of Buyer’s terms 

and conditions.

2. 

Payment/Prices. 

 Unless other arrangements have been 

made in writing between Seller and Buyer, payment for the 
product(s) shall be made upon receipt of invoice.  The prices 
shown on the face hereof are those currently in effect.  Prices 
invoiced shall be per pricelist in effect at the time of shipment.  
Prices are subject to increase for inclusion of any and all taxes 
which are applicable and which arise from the sale, delivery or 
use of the product(s), and the collection of which Seller is or 
may be responsible to provide to any governmental authority, 
unless acceptable exemption certificates are provided by Buyer 
in accordance with applicable law.  Buyer shall pay all charges 
for transportation and delivery and all excise, order, occupation, 
use or similar taxes, duties, levies, charges or surcharges 

applicable to the product(s) being purchased, whether now 

in effect or hereafter imposed by any governmental authority, 
foreign or domestic.

3. 

Warranty.

  SELLER MAKES NO WARRANTIES OR 

REPRESENTATIONS AS TO THE PERFORMANCE OF ANY 
PRODUCT EXCEPT AS SET FORTH IN THE STONEAGE 
LIMITED WARRANTY PROVIDED WITH THE PRODUCT.  

4. 

Delivery. 

 Seller is not obligated to make delivery by a 

specified date, but will always use its best efforts to make 
delivery within the time requested.  The proposed shipment 
date is an estimate.  Seller will notify Buyer promptly of any 
material delay and will specify the revised delivery date as 
soon as practicable.  UNDER NO CIRCUMSTANCES SHALL 
SELLER HAVE ANY LIABILITY WHATSOEVER FOR LOSS OF 
USE OR FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES 
RESULTING FROM DELAY REGARDLESS OF THE REASON(S).

All product(s) will be shipped F.O.B. point of origin, unless 
specifically agreed otherwise, and Buyer shall pay all shipping 
costs and insurance costs from that point.  Seller, in its sole 
discretion, will determine and arrange the means and manner of 

transportation of the product(s).  Buyer shall bear all risk of loss 

commencing with the shipment or distribution of the product(s) 

from Seller’s warehouse.  Order shortages or errors must 
be reported within fifteen (15) business days from receipt of 
shipment to secure adjustment.  No product(s) may be returned 
without securing written approval from Seller.  

5. 

Modification.

  These Terms and Conditions are intended by 

Seller and Buyer to constitute a final, complete and exclusive 

expression of agreement relating to the subject matter hereof 
and cannot be supplemented or amended without Seller’s prior 
written approval.  

6. 

Omission. 

 Seller’s waiver of any breach or Seller’s failure 

to enforce any of these Terms and Conditions at any time, shall 
not in any way affect, limit or waive Seller’s right thereafter to 

enforce and compel strict compliance with every term and 
condition hereof.  

7. 

Severability. 

 If any provision of these Terms and Conditions 

is held to be invalid or unenforceable, such invalidity or 
unenforceability shall not affect the validity or enforceability of 
the other portions hereof.

8. Disputes.

  Seller and Buyer shall attempt in good faith to 

promptly resolve any dispute arising under these Terms and 
Conditions by negotiations between representatives who have 

authority to settle the controversy.  If unsuccessful, Seller and 

Buyer shall further attempt in good faith to settle the dispute by 
nonbinding third-party mediation, with fees and expenses of 
such mediation apportioned equally to each side.  Any dispute 
not so resolved by negotiation or mediation may then be 
submitted to a court of competent jurisdiction in accordance 
with the terms hereof.  These procedures are the exclusive 
procedures for the resolution of all such disputes between the 
Seller and Buyer.

Summary of Contents for Warthog WT series





















Reviews: