StoneAge Warthog WT series User Manual Download | Manualshive

Page: 5 / 20

background image

5

866-795-1586 • WWW.SEWERNOZZLES.COM

WARNING AND SAFETY INSTRUCTIONS

WARNING

Because of the short length of the Warthog® WT, the tool can turn around in pipes and come back at
the operator at a high rate of speed. A rigid “stinger” should be used between the hose and the tool.
The rigid length of the tool including hose end must be 1-1/2 times the inside diameter of the pipe being
cleaned (see below).
Make sure there is an operator controlled dump in the system, operated by the person closest to the
cleaning job. It is recommended that the hose be marked a few feet from the end with a piece of tape so
the operator knows when to stop when retracting the tool.

DANGER

Operations with this equipment can be potentially hazardous. Caution must be exercised prior to and

during machine and water jet tool use. Please read and follow all of these instructions, in addition to the

guidelines in the WJTA Recommended Practices handbook, available online at

www.wjta.org

.

Deviating

from safety instructions and recommended practices can lead to severe injury and/or death.

IMPROPER USE:

WT will turn around in

large diameter pipe

VERY DANGEROUS!

PROPER USE:

WT with rigid “stinger”

to prevent turnaround, still

able to pass through elbows.

Rigid
Stinger

1-1/2 times

pipe ID

«
...
3
4
5
6
7
...
»

Summary of Contents for Warthog WT series





















Reviews:

No comments

Related manuals for Warthog WT series

Brand: Datalogic Pages: 32

Brand: TDR Pages: 2

Brand: Happijack Pages: 2

Brand: GeoVision Pages: 15

Brand: EHEIM Pages: 8

Brand: EHEIM Pages: 31

Brand: Essentials Pages: 2

Roklima Plus 4F

Brand: Rothenberger Pages: 80

Brand: Aqua One Pages: 8

Brand: iDTRONIC Pages: 7

Brand: Fabtech Pages: 9

Brand: IrisVision Pages: 80

HydroPower RO XXL

Brand: unGer Pages: 32

Brand: Eaton Pages: 65

Brand: Carrier Pages: 4

Brand: EasyPro Pages: 16

Brand: macromatic Pages: 2

Brand: MAHLE Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands