StreetStrider 8s Owner'S Manual Download

Page: 26 / 28

The specific warranty covering your

StreetStrider

is governed by the law of the state or country in which it was purchased, and

applies only to mobile elliptical devices purchased from StreetStrider.com.

Frames (Frame, Strider Skis, Strider Poles)

StreetStrider

frames are warranted by

StreetStrider

, 16331 Gothard St., Suite C Huntington Beach, CA 92647, against

manufacturing defects in materials and/or workmanship for a period of three (3) years from the date of original purchase.

Components

Components are warranted by their original manufacturer and not by

StreetStrider

. The Shimano internal geared hub is

warranted for a period of two (2) years according to the Shimano warranty (http://bike.shimano.com/content/sac-bike/en/

home/news-and-info/warranty.html). Joint bearings, drive parts, and frame fixtures are warranted against manufacturing

defects in materials and/or workmanship for a period of one (1) year and according to the individual components’

manufacturers, from the date of the original retail purchase.

Terms of Limited Warranty

This limited warranty is not meant to suggest or imply that the

StreetStrider

cannot be broken or will last forever. It does mean

that the

StreetStrider

is covered subject to the terms of the limited warranty.

• This limited warranty applies only to the original owner of a

StreetStrider

and is not transferable to subsequent

owners.

• This limited warranty applies only to

StreetStriders

assembled in full compliance with the instructions within this

Owner’s Manual.

•

Damage resulting from normal wear and tear, including the results of fatigue, is not covered. Fatigue damage is

a symptom of the frame being worn out through normal use. It is one kind of normal wear and tear, and it is the

owner’s responsibility to inspect his/her

StreetStrider

on a regular basis.

• This limited warranty is void if the

StreetStrider

is subjected to abuse, neglect, improper repair, improper maintenance,

alteration, modification, an accident or other abnormal, excessive, or improper use – to be determined by the

Company at its sole discretion.

• Personal injury,

StreetStrider

failure, loss or damage, abuse, neglect, normal wear and tear including the results of

fatigue, improper fit or maintenance by anyone other than StreetStrider.com, or use of parts inconsistent with the

use originally intended for the

StreetStrider

as sold are not covered by this warranty. In no event shall the Company

be liable for incidental or consequential damages that might arise as a result of improper use and/or failure of the

StreetStrider

•

For any warranty claim to be considered, the

StreetStrider

must be submitted through StreetStrider.com. The

StreetStrider

must be in assembled condition and accompanied by the original, dated sales receipt for the

StreetStrider

. Be sure to keep your receipt in a safe place.

•

All labor and transportation charges for warranty service are the responsibility of the StreetStrider’s owner.

During the duration of this Limited Warranty, the Company will either repair any defective frame or component, or, at our

option, replace any defective frame or component with the same or most nearly comparable model or component then

available.

THIS IS THE EXCLUSIVE REMEDY UNDER THIS WARRANTY. ANY AND ALL OTHER REMEDIES AND DAMAGES THAT MAY

OTHERWISE BE APPLICABLE ARE EXCLUDED, INCLUDING, BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR PUNITIVE DAMAGES.

Limited Warranty

Summary of Contents for 8s
























Search results

Summary of Contents for 8s

Reviews:

Related manuals for 8s

Brands by name

Popular brands

StreetStrider 8s, Owner'S Manual

Search results

Summary of Contents for 8s

Reviews:

Related manuals for 8s

Brands by name

Popular brands