StreetStrider 8s Owner'S Manual Download

Page: 7 / 28

DESCRIPTION

HARDWARE

SPECIFICATIONS

QTY

STATE

Front wheel rim and tire

Rim 36H, Tire 16” x 1 3/8”, ISO 37 x 349

80-85 psi

Front wheel hub

19 mm hex axle nut

M12 x P1.75 x L10 x W19, nylon lock

Tighten

Steering linkage

Inboard and outboard

rod ends

Threaded linkage rod

M8 x P1.25 x L20 x W14 flats on stud

M8 x P1.25 x L10 x W13 nylon lock nut

M8 x P1.25 x L20 rod, right and left thread ends

M8 x P1.25 x L5 x W14, right and left jam nuts

Lubricate balls

Tighten

Crank arm set with quick

release left side

Bottom bracket

8 mm hex screw

QR stem

Square taper

M8 x P1.0 x L15 x H12 x W8, 18 mm flange

M10 x P1.5 x L10 x W17, nylon lock

68 x 122 mm

Tighten

Snug

Tighten

Chain ring with guard

52 T

Chain

1/2” x 1/8” x 93 links

Lubricate

Rear wheel rim and tire

Rim 36 H, Tire 20” x 1 3/8”, ISO 37 x 451

80-85 psi

Internal gear hub

15 mm axle nuts

8 speed, 3/8” x 26 TPI x W15 axle nuts

Tighten

Front disc brake

5 mm hex mount screw

5 mm hex caliper screw

5 mm hex outer pad

3 mm hex inner pad

Cable housing adjuster

4 mm hex cable clamp

M6 x P1.0 x L15 x H10 x W5, through knuckle

M6 x P1.0 x L15 x H10 x W5, through bracket

W5 outer pad adjuster with 2 mm lock set screw

W3 inner pad adjuster, through center screw hole

M6 x P1.0 x L15 knurled for fingers with lock ring

M5 x P0.8 x L12 x H10 x W4, socket and nut

Tighten

Adjust-tighten

Adjust

Adjust-lock

Adjust-tighten

Steering knuckle w/

lean stop

5 mm hex screw

Lean stop disc

Composite bushing

M6 x P1.0 x L15 x H10 x W5, socket screw

W10 nylon lock nut

OD24 x T4 with 6 mm offset hole

OD12 x ID10 x L15 x 17 mm flange

Adjust-tighten

Grease

King pin bolt in front beam

clevis

8 mm hex bolt

washer

17 mm nut

M10 x P1.5 x L75 x H15 x W8, socket

OD16 x ID10 x T1

M10 x P1.5 x L10 x W17, nylon lock

Snug but allow

knuckle swivel

Front disc rotor

4 mm hex screw

M5 x P0.8 x L10 x H10 x W4, Rotor 120 mm

Tighten

Rear disc brake

5 mm hex mount screw

5 mm hex caliper screw

5 mm hex outer pad

3 mm hex inner pad

Cable housing adjuster

4 mm hex cable clamp

M6 x P1.0 x L15 x H10 x W5, through drop out

M6 x P1.0 x L15 x H10 x W5, through bracket

W5 outer pad adjuster with 2 mm lock set screw

W3 inner pad adjuster, through center screw hole

M6 x P1.0 x L15 knurled for fingers with lock ring

M5 x P0.8 x L12 x H10 x W4, socket and nut

Tighten

Adjust-tighten

Adjust

Adjust-lock

Adjust-tighten

Rear disc rotor

4 mm hex screw

M5 x P0.8 x L10 x H10 x W4, Rotor 140 mm

Tighten

Rear drop out

Dropout slot for rear hub axle

Holes for rear brake mounting bracket

M5 x P0.8 hole for rear luggage rack screw

Specification

Key

M=OD of threads, mm

L=length

W=wrench fit, mm

P=pitch, threads/mm

H=OD of head

T=washer thickness, mm

TERMINOLOGY: The right and left sides of the StreetStrider refer to sides when one is striding.

IMPORTANT:

Save the box and packing material as they must be used to repack the StreetStrider for any returns.

Summary of Contents for 8s
























Search results

Summary of Contents for 8s

Reviews:

Related manuals for 8s

Brands by name

Popular brands

StreetStrider 8s, Owner'S Manual

Search results

Summary of Contents for 8s

Reviews:

Related manuals for 8s

Brands by name

Popular brands