background image

1.0 INTRODUCTION

1.1 Safety Instructions

DO NOT INSTALL YOUR RECEIVER

 

„

In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which 

might obstruct the ventilation slots.

DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:

 

„

To direct sunlight or any other equipment that generates heat; to rain or intense moisture; to intense vibration 

and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as 

loudspeakers, transformers, etc.

 

„

Do not use a damaged power cord. It may cause a fire or an electric shock. Do not touch a power cord with wet 

hands. It may cause an electric shock.

 

„

When the receiver is not used for a long period of time, you should unplug the power cord from the wall socket.

 

„

Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you may clean your receiver with 

a soft lint-free cloth slightly made damp with a mild soap solution, and only after disconnecting from the mains 

voltage supply. Make sure no foreign objects fall through the ventilation slots because this could cause fire or an 

electric shock.

 

„

Do not place any objects on top of the receiver because this might prevent proper cooling of the components 

inside.

Safety Precautions

 

„

Never try to open the receiver. It is dangerous to touch the inside of the receiver due to high voltages and 

possible electrical hazards. Opening the receiver will void the warranty of the product. Refer all maintenance or 

servicing to suitably qualified personnel.

 

„

When you are connecting cables, be sure that the receiver is disconnected from the mains supply voltage. Wait a 

few seconds after switching off the receiver before you move the receiver or disconnect any equipment.

 

„

It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical 

power consumption of the installed equipment. Please ensure that the electrical power supply corresponds with 

the voltage on the electrical identification plate at the back of the receiver.

If the receiver does not operate normally even after strictly following the instructions in this user manual, it is 

recommended to consult your dealer.

WEEE Directive

Correct Disposal of this product. This marking indicates that this product should not be disposed with other 

household wastes throughout the EU. To prevent possible harm to the environment or human health from 

uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. 

To return your used device, please use the return and collection systems or contact the retailer where the 

product was purchased. They can take this product for environmental safe recycling.

1.2 Storage

Your receiver and its accessories are stored and delivered in a packaging designed to protect against mechanical 

shocks and moisture. When unpacking it, make sure that all the parts are included and keep the packaging away from 

children. When transporting the receiver from one place to another or if you are returning it under warranty conditions, 

make sure to repack the receiver in its original packaging with its accessories. Failing to comply with such packaging 

procedures could damage the product and void your warranty.

1.3 Equipment Set-up

We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions 

below:

 

„

Refer to the user manual of your TV.

4

Summary of Contents for SRT 3030


























Reviews: