background image

 

IMPORTANT SAFETY CONSIDERATIONS

 

JACK STANDS

 

USE AND CARE 

 

Do not modify the jack stands

 

in any way.

 Unauthorized modification may impair the function 

and/or safety and could affect the life of the equipment. There are specific applications for which 

the 

jack stands

 were designed. 

 

Always check of damaged or worn out parts before using the jack stands. 

Broken parts will 

affect the 

jack stands

 operation. Replace or repair damaged or worn parts immediately.

 

Store idle jack stands. 

When 

jack stands

 are not in use, store them in a secure place out of the 

reach of children. Inspect it for good working condition prior to storage and before re-use. 

 

WARNING! 

NEVER

 

use automotive jack stands to support both ends, or one side of 

a vehicle! Use only 1 pair per vehicle. Rated capacity is per pair only! 

 

INSPECTION 

 

Inspect the jack stands carefully before each use. Ensure the jack stands are not damaged, 

excessively worn, or missing parts.   

 

Do not use if components are bent, broken or cracked. 

 

Using jack stands that is not in good clean working condition may cause serious injury.   

 

Inspect the work area before each use. Make sure it is free and clear of any potential hazards. 

 

WARNING:

 The warnings, cautions, and instructions discussed in this instruction manual 

cannot  cover  all  possible  conditions  or  situations  that  could  occur. 

It  must  be  understood  by  the 

operator that common sense and caution are factors that cannot be built  into this product,  but must be 

supplied by the operator. 

 

SAFETY MARKINGS 

  WARNING! 

1. 

Study, understand, and follow all instructions before operating this device. 

2. 

Do not exceed rated capacity. 

3. 

Use only on hard, level surfaces. 

4. 

Center load on saddle. 

5. 

Use as a matched pair only. 

6. 

Stands are not to be used to simultaneously support both ends of a vehicle. 

7. 

No alterations shall be made to this product.           

8. 

Support only on areas of the vehicle as specified by the vehicle manufacturer. 

9. 

Only attachments and/or adapters supplied by the manufacturer shall be used. 

10.  Use wheel chocks or other blocking device on opposing wheels before using jack stands. 

11.  Do not use jack stands for any use other than the manufacturer specified usage. 

12.  Do not use if damaged in any way. 

13.  Failure to heed these markings may result in personal injury and/or property damage. 

Summary of Contents for 46223








Reviews: