background image

Page 11 of 16 

 

Operating Instructions 

WARNING

 

 

Electric shock hazard. Do not expose to water or rain.  

 

Do not use this product with any solid-state speed control device.  

 

Rotating blade hazard. Can cause serious injury or cut. Keep hands clear.  

 

DO NOT operate without guards in place.  

1.  Plug the fan into the grounded power outlet. 

2.  Direct the fan to the area of desired air flow. Select the blade speed by setting the switch to 

HIGH 

(2), 

LOW

 (1), or 

OFF

 (0). 

NOTE: It is expected that the motor will feel warm to the touch after continuous operation. This fan 
features a thermostat that will automatically shut offif it overheats for any reason. If this happens, 
immediately unplug the fan from the outlet. Wait approximately 15 minutes before plugging the fan 
back in. 

Locking Wheel Instruction for Model #79031 

1.  When the wheels are unlocked, the fan can roll in any direction.   

2.  When wheels are in the locked position, the fan will not roll.   

 

 

AfterEach Use 

WARNING

 

 

Be sure no parts of the fan are damaged. 

Be sure the fan speed control is in the OFF position. 

Maintenance 

WARNING

 

 

Turn power OFF and unplug fan before servicing. 

 

Summary of Contents for 49934

















Reviews: