background image

Page 12 of 16 

 

Recharging the Battery 

WARNING

 

 

Always ensure that internal battery is fully charged. Do not overcharge the battery. 

 

Leaving a battery in a discharged state or without recharging every 90 days may result in 
permanent damage to the battery and poor boosting performance. 

 

Do not use the AC or DC outlets while the power pack is being charged. Doing so may damage 
the charging adapter. 

 

Do not attempt to recharge the internal battery if it is frozen. 

 

Use the supplied AC charger to recharge the unit. 

 

Recharge the unit every 90 days to maintain maximum battery capacity and extend unit life.  

Recharging the jump starter: 

1. Turn off all accessories before recharging. 

2. Plug one end of the included AC charger into charging input port of the jumpstarter and the other 
end into 115V AC electrical socket. 

3. The charging indicator flashes red intermittently to indicate that the battery is charging. 

Maintenance 

Maintain the jumpstarter by adopting a program of conscientious repair and maintenance in 
accordance with the following recommended procedures. It is recommended that the general 
condition of any jumpstarter be examined before it is used. Keep your jumpstarter in good repair. 
Keep handles dry, clean, and free from oil and grease. The following chart is based on a normal 
operation schedule. 

 

Maintenance Interval 

Maintenance Point 

Before operating or after using

 

Clean the exterior surface of the jumpstarter with a damp cloth 
to prevent accumulation of dust and dirt. 

After using  

Make sure USB/LED Slide Switch to the middle(OFF position) 

Make sure ON/OFF Power Switch to OFF position after use. 

Make sure disconnecting the 12V DC appliances after use to 
avoid over discharge of jumpstarter

’s internal battery 

Make sure the plastic covers on the 12V DC outlet are closed 
after use. 

Extending battery lifespan 

Recharge the battery at least once every 90 days. This will 
extend the durability and efficiency of the battery. 

 

Troubleshooting 

Use the table below to troubleshoot problems before contacting service personnel or your local 
dealer. If the problem continues after troubleshooting, call your local dealer for assistance. 

 

Summary of Contents for 53011

















Reviews: