background image

E M E R G E N C Y /
S E RVICE  B R A K E
L E V E R

By pushing fully forward
on Lever (A) the brakes
will be engaged.

Brakes will lock if Lever
(A) 

is 

pushed 

fully

forward and is drawn in
toward operator, allowing
it  to  hook  behind  the
extended  Carriage  Bolt
lock tab.

LEFT & RIGHT TRACK CONTROLS

To move straight ahead

, simultaneously push

both Left and Right Track Controls forward.

To move straight rearward

, simultaneously pull

both Left and Right Track Controls rearward.

To turn right sharply

, push forward on Left Tr a c k

Control while leaving Right Track Control in neutral.

To turn left sharply

, push forward on Right Track

Control while leaving Left Track Control in neutral.

To  counter-rotate  Tr a c k s

(shortest  turn  possible),

push one Track Control forward while simultaneously
pulling rearward on the other Track Control.

N O T E

:  When  either  Track  Control  is  "slowly"

released, it will automatically return to neutral. Never
allow Track Controls to "snap" back to neutral.  See
Operation section of this Manual for further
i n s t r u c t i o n s .

RELEASING SEAT PAN

Release the seat latch on the front center of the
the seat pan assembly (1).  Rotate the Seat/Cover
Assembly (2) all the way to the rear until it hits its
stop [back edge of the Cover acts as a stop].

ADJUSTING SEAT POSITION

To  slide  Seat  forward  or  back,  push  Seat
Adjustment Lever (3) (under the lower left corner of
the Seat) outwardly to release Seat.  Set Seat's
new position, then release Lever to lock in position.
Seat Assembly can be installed at three diff e r e n t
locations on Cover using alternate hole patterns.

C H O K E
CONTROL

Pull Choke Control
out (up) toward
operator, to
increase amount of
Engine choking
(On position).  Push
Choke Control in
(down)  away  from
operator, to
decrease amount
of  Engine  choking
( O ff position).

THROTTLE CONTROL

Turn Throttle Control 1/4 turn counter clockwise to
unlock.  Pull Throttle Control out (up) toward
operator, to increase Engine speed. Push Throttle
Control in (down) away from operator, to decrease
Engine speed.  Turn handle 1/4 turn clockwise to
lock setting (Do not over-tighten!)

T

RACK

D

RIVE

C

ONTROLS

Neutral

Reverse

Forward

Neutral

Reverse

Forward

L

E

F
T

R

I

G
H

T

A

1

2

3

T H R O T T L E

pull out

1/4 turn

to lock

C H O K E

PULL OUT

Summary of Contents for MD750

























Reviews: