background image

OVERVIEW 

 

 

These Structural Concepts display cases are 

designed to merchandise packaged products at 

ambient temperatures.  

 

Refrigerator unit has its own operating manual. 

 

Cases should be installed and maintained according 

to this operating manual’s instructions to ensure 

proper performance. Improper use will void warranty. 

 

COMPLIANCE 

 

 

Performance issues when in violation of applicable 

NEC, federal, state and local electrical codes are not 

covered by warranty. See below. 

OVERVIEW / COMPLIANCE / PRECAUTIONS / WARNINGS / WIRING DIAGRAM 

WARNING  

  

Risk of electric shock. Disconnect power before servicing unit. 

CAUTION!  More than one source of electrical supply is  

employed with units that have separate circuits.   

Disconnect ALL ELECTRICAL SOURCES before servicing. 

 

WARNING 

ELECTRICAL 

  HAZARD

 

COMPLIANCE 

 

This equipment MUST be installed in compliance with 

all applicable NEC, federal, state and local  

electrical codes. 

CAUTION! LED LAMP REPLACEMENT GUIDELINES 

 

LED lamps reflect specific size, shape and overall design.   

Any replacements must meet factory specifications. 

CAUTION

 

CAUTION!  GFCI BREAKER USE REQUIREMENT 

 

If N.E.C. (National Electric Code) or your local code                                                  

requires GFCI (Ground Fault Circuit Interrupter) protection,                                

you MUST use a GFCI breaker in lieu of a GFCI receptacle. 

ATTENTION               

CONTRACTORS

 

PRECAUTIONS AND WARNINGS 

 

 

This page contains an important precautions and 

warning to prevent injury or death.  

 

Please read carefully! 

 

WIRING DIAGRAM 

 

 

Each case has its own wiring diagram folded and in its 

own packet. 

 

Wiring diagram placement may vary; it may be placed 

near ballast box, field wiring box, raceway cover, or 

other related location.

 

WARNING: This product can expose you to chemicals, including 

 Urethane (Ethyl Carbamate), which are known to the state of  

California to cause cancer and birth defects or other reproductive  

harm. For more information go to P65Warnings.ca.gov.

 

WIRING DIAGRAM FORMAT & LOCATION 

 

 

Each case has its own wiring diagram folded & in its own packet. 

 

Wiring diagram placement may vary; it may be placed near field     

wiring box, raceway, or other related location. 

Summary of Contents for Addenda SHS9251


















Reviews: