background image

15 

GENERAL CLEANING [TO BE PERFORMED BY STORE PERSONNEL] 

Cleaning 

Daily 

Weekly  Monthly 

Task 

 

Clean Case Exterior 

 

 

 

Clean side glass, front curved glass and the 
sliding rear door glass (swinging door is        
optional on HMG2653) with a household or 
commercial glass cleaner and soft cloth.  

 

 

 

Clean wood, laminate and painted surfaces, 
and rear ledge with a warm soap and water  
solution and soft cloth.  Never use wire cloth or 
abrasive cleaners on case.  

 

 

 

Remove rear doors and clean door and door 
channel with a household or commercial 
cleaner. 

 

 

 

Vacuum under case to remove all dust and dirt 
that may collect under case.

 

Clean Case Interior 

 

 

Glass shelves can be cleaned with a household 
or commercial glass cleaner. 

 
 

 
 

 

 

Deck and/or non-glass shelves can be cleaned 
with a warm soap and water solution and soft 
cloth.  For stubborn stains/residue, decks and 
non-glass shelves can be removed and cleaned 
with soap and water solution or submersed in 
hot, soapy water solution.  Rinse thoroughly. 
Dry.  Return to case. 

 

 

 

Remove the deck and clean with soap and    
water solution and soft cloth. 

 

 

 

Remove crumb tray.  Submerse in warm soap 
and water solution and clean with soft cloth.  
Allow to dry and return to case. 

Summary of Contents for Harmony HMG2653



















Reviews: