background image

OVERVIEW / COMPLIANCE / WARNINGS / PRECAUTIONS 

OVERVIEW 

 



These cases should be installed and operated 
according to these instructions to insure proper 
performance.  Improper use will void warranty. 



This unit is designed for the display of products in 
ambient store conditions where temperatures and 
humidity are maintained at a maximum of 75 °F 
and 55% relative humidity. 

 

COMPLIANCE 

 



Performance issues when in violation of applicable 
NEC, federal, state or local electrical codes are not 

WARNING  

  

Risk of electric shock.  

Disconnect ALL ELECTRICAL SOURCES before servicing. 

 

WARNING 

ELECTRICAL 

  HAZARD

 

COMPLIANCE 

 

This equipment MUST be installed in compliance with 

all applicable NEC, federal, state and local  

electrical and plumbing codes. 

CAUTION 

CAUTION 

 

Fluorescent lamps have been treated to resist breakage  

and must be replaced with similarly treated lamps. 

CAUTION 

 

LED lamps reflect specific size, shape and overall design.   

Any replacements must meet factory specifications. 

CAUTION 

CAUTION 

 

If N.E.C. (National Electric Code) or your local code                                   

requires GFCI (Ground Fault Circuit Interrupter) protection,                            

the use of a GFCI breaker is strongly recommended. 

covered by warranty. 



See compliance specifics below. 

 

WARNINGS 

 



Following are important warnings to prevent 
injury or death. 



Please read carefully! 

 

PRECAUTIONS 

 



Following are important precautions to prevent 
damage to unit or merchandise. 



Please read carefully! 

Summary of Contents for Harmony HMG2653



















Reviews: