background image

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / PLUGS / WIRING  -  PAGE 2 of 2  

CAUTION!  GFCI BREAKER USE RECOMMENDATION 

 

If N.E.C. (National Electric Code) or your local code                                  

requires GFCI (Ground Fault Circuit Interrupter) protection,                           

the use of a GFCI breaker is strongly recommended. 

CAUTION!  ADVERSE CONDITIONS / SPACING ISSUES 

 



Performance issues caused by adverse conditions are NOT warranted. 



End panels must be tightly joined or kept at least 6-inches away  from 
any structure to prevent condensation. 



Unit must be kept at least 15-feet from exterior doors, overhead HVAC 
vents or any air curtain disruption to maintain proper temperatures. 



Unit must not be exposed to direct sunlight or any heat source     
(ovens, fryers, etc.). 



Tile floors, low ceilings or small rooms increase noise level.  Whisper 
Cool compressor blankets or remote units resolve noise level issues. 



Keep at least 8-inch clearance above unit for air discharge                 
(self-contained units only). 

CAUTION 

CAUTION!  LAMP REPLACEMENT GUIDELINES 

 

LED lamps reflect specific size, shape and overall design.   

Any replacements must meet factory specifications. 

 

Fluorescent lamps have been treated to resist breakage and                  

must be replaced with similarly treated lamps. 

CAUTION 

PRECAUTIONS 

 



This sheet contains important precautions to prevent 
damage to unit or merchandise. 



Please read carefully! 



See previous page for specifics on 

OVERVIEW, NSF 

TYPE, COMPLIANCE 

and 

WARNINGS.

 

WIRING DIAGRAM 

 



Each case has its own wiring diagram folded and in its 
own packet. 



Wiring diagram placement may vary; it may be placed 
near ballast box, field wiring box, raceway cover, or 
other related location.

 

CAUTION! CHECK EVAPORATOR PAN POSITION AND PLUG 

 

Water on flooring can cause extensive damage!  

 

 Before powering up unit, check the following: 

 



Evaporator pan MUST BE positioned directly under condensate drain. 



Evaporator pan plug MUST BE securely plugged into receptacle.   

CAUTION!  POWER CORD AND PLUG MAINTENANCE 

 

 

Risk of electric shock.  If cord or plug becomes damaged,                       

replace only with cord and plug of same type.   

Summary of Contents for Oasis CO2739R






















Reviews: