Studer C1312 COMPACT User And Installation Manual Download

Page: 13 / 23

STUDER INNOTEC

COMPACT

User manual

COMPACT V2.0 E

4.2 Light Emitting Diodes:

LED

Marking

LED lit

LED blinks

Voltage corresponding to self-
adjusted values is at the AC IN
input.

Voltage, outside of the self-
adjusted values is at the AC IN
input.

CHARGER

Battery Charger is working

The input voltage is out value
(voltage or frequency)

3 SOLAR

CHARGE

Connected Solarmodules are
delivering energy

Program

Program mode for Aux. Contact

Contact active Auxiliary Contact is activated

Contact manual Aux. Cont. manually activated

Transfersystem is active. In-
coming voltage is being sent
directly to AC OUT outlet

AC OUT

There is voltage at the AC OUT
outlet

The Inverter is in Standby-Mode

INVERTER

Inverter is working

Forced -Inverter Mode

Over Temp.

For the time being the COMPACT
is out of service because of
overheating.

Overload

The COMPACT is out of service
because of overload or short-
circuit

Batt. Low/High Battery voltage is too low

Battery voltage is too high

OFF

COMPACT is turned off. Turning it
back on is only possible manually.

COMPACT is for the time being
turned off. Turning it back on will
follow automatically!

Battery Charger and or Solar
Charge Regulator are doing an
equalization cycle

15–18

Charge

condition

Battery

LED 15 – Absorbtion time is
running

25 CURRENT

MONITOR

Display the value of the output power in % of Pnom (in Inverter Mode)
and the charge current in Amps. (in Charger Mode) In this mode the
200% LED indicate that power sharing is in use.

4.3 Push

buttons:

ON/OFF

Turning the COMPACT on and off (Help Button for Programming)

RESET

Alarm Signal off (Help Button for Programming)

Aux. Contact

Control Aux. contact (Help Button for Programming)

4.4 Turning

Knobs:

CHARGER

Adjustment for max. Charging Current (Not for Solar charge regulator)

TRANSFER

Adjustment for Transfer Voltage Threshold(TRANSFER – INVERTER)

STANDBY

Adjustment for „Standby“ system

INPUT LIMIT

Must be adjusted to the maximal available current of your AC INPUT
supply (see on chap.

4.6.3)

Summary of Contents for C1312 COMPACT
























Search results

Summary of Contents for C1312 COMPACT

Reviews:

Related manuals for C1312 COMPACT

Brands by name

Popular brands

Studer C1312 COMPACT, User And Installation Manual

Search results

Summary of Contents for C1312 COMPACT

Reviews:

Related manuals for C1312 COMPACT

Brands by name

Popular brands