14
15
DESCRIPTION OF THE DEVICE
The device consists of the following main components:
STARTING UP / QUICK GUIDE
This quick guide helps practised users set up the device in a few steps. For detailed start-up
instructions, please consult the next chapter.
1.
Control panel
2.
Air outlet (do not cover)
3.
Dehumidifier
4.
– «POWER» On/off switch and control
displays:
– «WATER FULL»: Water tank is full
– «RUN»: Device operating
– «DEFROST»: Defrost function for the
evaporator
5.
– «Speed»: Air volume (1-2)
6.
– «TIMER»: Autom. power on/off
(1, 2, 4 or 8 h)
7.
– «HUMID» Humidity (40, 50,
60 % rel. and continuous operation)
8.
Handle
9.
Air intake (do not dover)
10.
Outlet pipe connector
11.
Handle for water tank
12.
Water level gauge
13.
Opening flaps for water tank
14.
Handle for water tank (opened out)
15.
Cover for water tank
16.
Filter mounting bracket
17.
Air intake filter
18.
Air intake cover
19.
Opening flaps
20.
Outlet pipe ø 8/10 mm (internal/external
diameter; not included)
21.
Connector for outlet pipe
22.
Water tank cover (removed)
23.
Water tank handle
24.
Water level float
25.
Transparent water tank
2.
1 hour
Opening flaps
5.
6.
6.
6.
6.
5.
2.
Opening flaps
1.
Place the device on a stable and water-proof surface. Do not
place directly on a carpeted or wooden floor.
Important: to ensure that the compressor has not sustained
any damage after transportation of the device, wait at least an
hour before operation (no warranty). Ensure the device is up-
right when transported and never lay flat.
2.
Pull out the opening flaps (13) on the reverse and remove the
water tank. Ensure that there is no packaging material inside.
If there is not, return the water tank to its position and ensure
it snaps into place.
3.
Plug in the power plug (all LEDs will light up red briefly). Do not
connect to a timer or switched cable connector.
4.
For optimal functioning, close the windows
and doors.
5.
Switch on
: Press «POWER»
(«
RUN
» will light up, the air outlet flaps will
open and the fan and compressors will
start).
Switch off
: Press «POWER» again.
Good to know:
– If the dehumidifier has been turned off shortly beforehand, the
compressor will start with up to 3 minutes’ delay (= protective
circuit).
– «Water Full»
à
Water tank is full
à
empty tank
à
p. 16.
– «Defrost»
à
Defrost process started
à
p. 17.
6.
Displays/settings:
–
«SPEED»
à
Changing of air volume - low «1»/high «2».
–
«TIMER»
à
Device switches on or off automatically after 1,
2, 4 or 8 hours .
–
Automatic switch-on:
First switch the device off and then
press the «TIMER» button until the required time is displayed.
If no LED lights up, the timer function is switched off.
–
Automatic switch-off:
Just as with the «Automatic switch-on»
function, turn on the device first and then press the «TIMER»
button until the required time is displayed. If no LED lights up,
the timer function is switched off.
–
«HUMID»
à
Set humidity.
«Continue»
à
Continuous operation to ensure dehumidifi-
cation process is as fast as possible. «40, 50, 60 %»
à
Re-
quired humidity in % rel. (40 % = dryer, 60 %= damper)
7.
«
WATER FULL
»
= Water tank full:
– WATER FULL»
à
Water tank full; compressor will switch off
à
Empty tank
– A pipe can also be attached (not included)
à
p. 17.
–
Remove water tank
à
Pull out the two opening flaps (13) on
the reverse of the tank. Hold the tank with the blue carry han-
dle and empty down the sink (the white lid does not need to be
removed when emptying the tank).
Good to now
:
Do not use the water for other purposes (contains dirt parti-
cles from the air). Clean the inside of the tank on a monthly ba-
sis
à
Hygiene.
–
Reset water tank
à
Fold down carrier handle
à
Reposition
water tank until it snaps into place («WATER FULL» will disap-
pear and compressor will start, after a short delay).
Downloaded from www.vandenborre.be
