background image

7 OF 12

PART NUMBER

H001SFJ600

ISSUE

00

DATE

18 Jul 2013

SUBARU OF AMERICA

FIGURE T

FIGURE U

7

NOTE: Use caution while installing the wiring harness, be sure to

route and attach the harness away from sharp metal surfaces.

8-PIN IGNITION SWITCH CONNECTIONS, continued

1. Verify that the tilt/telescoping steering column is still all the way out and

down.

2.  Reaching up from under the steering column, route the remote start ignition

harness up toward the vehicle’s instrument panel routing the remote start

ignition harness over the steering column with the vehicle’s instrument panel

harness.  Using two (2) of the supplied 39cm (15”) tie wraps, secure the

remote start ignition harness to the top of the vehicle’s instrument panel

harness on each side of the steering column (Tie Wrap #5 and Tie Wrap #6).

(FIGURE R) NOTE: Tie wraps #3 & 4 are indicated for reference.  These are

the same tie wraps called out in FIGURE Q from an alternate view.

3. Route the remote start ignition harness down towards the vehicle automatic

transmission (A/T) control module.  Using one (1) of the supplied 39cm (15”)

tie wraps (Tie Wrap #7), secure the remote start ignition harness to the

vehicle wiring near the A/T control module.  (FIGURE S)  NOTE: Tie wrap #6

is also shown as reference.

4-PIN & 2-PIN PRE-FIT CONNECTIONS LEFT CENTER of STEERING COLUMN

1.  Locate the vehicle’s 4-pin and 2-pin pre-fit connections located to the left

center of the steering column located near the left side lower dashboard

airbag / knee bolster mount.  These connectors are secured to the vehicle

wiring using  breakaway tape.  (FIGURE T)

2.  When the 2-pin pre-fit connector is located, unplug and discard the mating

wire jumper.  (This is used for the power window interrupt circuit)

3.  Plug the remote start pre-fit jumper harness 4-pin and 2-pin male connectors

into the corresponding 4-pin and 2-pin vehicle female connectors.

(FIGURE U)

WIRE HARNESS CONNECTIONS, continued

VIEW FROM UNDERSIDE OF

STEERING COLUMN

FIGURE S

STEERING

WHEEL

3

4

5

6

FIRE

WALL

FIGURE R

6

7

A/T

Control

Module

Summary of Contents for H001SFJ600

























Reviews: