background image

6

Trigger

Trigger

Bumper block

This is where the doors meet.

3

 [  ] : When cover cap 

  (option) is used.

Trigger

Trigger

Door width - 361

[Door width - 363]

3

Door width - 361

[Door width - 363]

3

30

I

4.5

30

I

4.5

30

I

4.5

30

I

4.5

187.5

187.5

Positions of Trigger for In Line Sliding

APPENDIX 3

Process holes according to the drawing below.

Bumper block should be inserted together 
with soft closers before installing upper track.

 CAUTION

Use the track for standard sliding for this application.

 CAUTION

When Vertical Frame is not Used

How to remove door

Spanner

wrench

Lever

APPENDIX 1

Use a 10 mm support under the door.
Then pull out the upper roller main unit from the door while raising 
the lever.

It will be easier if you slide the hanger bolt with a spanner.

Be careful not to let the door fall.

 

CAUTION

Bumper block

(Sold seperaterly)

Bumper block

(Sold seperaterly)

Door stopper

(Option)

Door stopper

(Option)

Min.13

Min.13

APPENDIX 2

When vertical frame is not used, use the 
door stopper

 and bumper block

⑦ 

on 

WKHWUDFNDQGRQWKHÀRRU

Fasten the door stopper at the location 
where the door will stop. Fix the bumper 
block to both the upper track ends, then 
adjust it to the position where the door 
closes.

The soft closer may be damaged 
if door stopper and bumper block 
are not installed.

 CAUTION

Summary of Contents for LAMP FD35EV









Reviews: