Sulion 2174990, Manual

13

12

ENGLISH 

ENGLISH 

Calle Verano, 51 - Polígono Industrial Las Monjas -28850 Torrejón de Ardoz - Madrid (ESPAÑA)

www.sulion.es

CIF  A28763647

+34 916774540

ATC: 

916749481 - info@sulion.es  /  

SAT :

 916749483 - sat@sulion.es

Remote control

Instructions for synchronizing the 

receiver and the remote control

The control is already factory-linked with its receive. 

Make sure all connections are correctly made.

Make sure that the remote control contains batteries.

Make sure that all switches (main and isolation) are on.

The control of this fan have two mode of synchronization, 

Universal mode and Unit mode:

- Unit Mode:

This type of synchronization allows you to control two or 

more nearby fans independently, each with its remote con-

trol.

Synchronization:

The control of this fan does not require synchronization 

with the receiver, the control is already factory-linked with 

its receiver

- Universal Mode:

This type of synchronization allows you to control one or 

more nearby fans with the same remote control.

Synchronization:

1.-Connect the power (wall switch) of the fan or fans that 

you want to control, and then just within the following

15 seconds, press the key   of the remote control for 10 

continuous seconds.

2.-A “beep” sound indicates that the connection has been 

executed and the equipment can function normally.

3.-Now, transmitter and receiver of the fan / s will have 

been synchronized. Turn off the fan / s current using the

switch or automatic and then turn it back on / s, this step 

is the one that closes the synchronization process.

It is not possible for a controller to forget a fan once it has 

been linked, if you want a fan to leave

to obey a command, another one must be linked to 

“overwrite it”.

Preparing for installation

Note: 

The estimated installation time is 120 minutes. This 

product can only be installed by a certified electrician Ca-

refully separate the fan’s parts, avoiding the use of cutters 

or blades that could scratch any part of it.

Remove the fan from the packaging carefully, avoiding the 

use of knives which could scratch any part of it.
Remove all the components. Place the motor on a cloth or 

wet surface so as not to damage its surface finish. Carefully 

handle the unit to make sure that its casing does not bend 

or get scratched.
The fan must be mounted on the floor or a large enough 

table to prevent any component from falling off.

Inverter

Timer

Nature wind

Turn off fan

Turn off light

Speeds

Change 

color 

temperature

Change 

light

intensity

Summer /

Winter

2H

2h

Rotation direction: summer and winter

The sliding switch controls the direction, whether clockwi-

se or counterclockwise.

Summer option/down - 

he downwards air current creates 

a refreshing effect as indicated in diagram A.

Winter option/up -

 An ascending air current pushes hot 

air away from the fan area near the ceiling, as indicated 

in diagram B. This allows you to use less central heating.

Maintenance and information of warranty

Maintenance and cleaning:

1.  The fan‘s natural movement can cause certain con-

nections to loosen. Check mounting connections, 

fastening parts, and blade accessories twice a year. 

Check that they are well fastened.

2.  Clean the fan periodically to help maintain its new 

appearance. Do not use water to clean it, as this may 

damage the motor or the wood, or could cause elec-

trical shock.

3.  Use a soft brush or microfiber cloth not to scratch the 

finish. The veneer is sealed with a layer of lacquer to 

minimize discoloration or loss of shine.

4.  It is not necessary to oil the fan. The motor contains 

bearings with permanent lubrication.

5.  Note: 

Failure to comply with these instructions results 

in the loss of the equipment warranty

.

6. Warranty service:

The manufacturer’s warranty covers real failures that may 

occur but not minor complaints such as the noise genera-

ted by the device, as all electric motors generate a certain 

amount of noise.

Operating the fan with slightly loose components (screws 

not adequately tightened) or the deformation of blades 

due to excessively vigorous cleaning may cause exces-

sive noise and wobbling, which will not be covered by the 

warranty. Taking regular care to retighten elements and 

clean carefully is enough to prevent these problems.

Control:

The device’s warranty will be invalid if it is installed for use 

with a solid-state wall switch or dimmer. It must only be 

used with the remote control provided with the unit.

Fan installation:

According to the terms and conditions of our warranty, this 

fan can only be installed by a certified electrician. Fans 

that are installed incorrectly can be dangerous to people 

and very expensive to repair, and will lose their warranty. 

This fan is designed for interior use only, excluding moist 

areas and bathrooms. The supplier does not assume any 

liability for physical or bodily damage caused by the in-

correct use or installation of the fan. If you are unsure, 

consult an electrician.

Wobbling:

All ceiling fans tend to wobble during their operation. A 

wobble of 2 cm is perfectly acceptable and does not indi-

cate any malfunction nor will it cause the fan to fall, as long 

as it was mounted to the ceiling correctly following the 

instructions in this manual. This ceiling fan has a comple-

tely secure mounting system that uses steel brackets and 

connecting spheres to allow it to rotate and to prevent the 

transmission of vibrations to the ceiling structure. Please 

note that even fans of the same model can have different 

wobbles, which is totally acceptable and does not imply 

any malfunction or manufacturing defect.

Increased perception of noise during 
nighttime operation:

The manufacturer’s warranty does not cover the fact that 

during the night, when the surrounding environment is 

quieter, the fan’s operating noise is more apparent. In ad-

dition, during the night, the power supply may experience 

alterations that may produce increased noise generated by 

the device, which does not indicate any malfunctioning or 

manufacturing defect in the device.

Fan lighthing system:

Noises and vibrations can be greater when the lighting sys-

tem is turned on. For example, the light diffuser can pro-

duce a slight buzz if not adequately attached. Once again, 

non-aggressive care and regular check to ensure that all 

elements are properly fastened will prevent these distur-

bances. Glass light diffusers are covered by the warranty to 

the distributor warehouses, and are subject to verification 

during delivery.

Warranty:

Manufactures guarantees the proper functioning of this 

equipment, repairs or spare parts of the model owing to 

faulty manufacture during 3 years after the surrender date, 

8 years exclusively in the case of the fan motor. Responsi-

bility will not be accepted, however, for damages or injury 

caused through misuse. For any claims the sale ticket must 

be presented. The company agrees to repair any defect or 

malfunction found in the item and any damages said de-

fect or malfunction might directly provoke. If the repara-

tion should fail to satisfy the customer and/or the object 

fail to present the optimum condition for the use to which 

it is destined the guarantee holder will have the right to 

the substitution of the acquired item for another identical 

characteristics or a complete refund of the purchase price. 

Terms and conditions of warranty

 www.sulion.es