SECTION 1
15
and actions and shall be initiated only by Autho-
rized Persons and done in the following sequence:
1. Review the equipment or machine to be
locked and tagged out.
2. Alert operator and supervisor of which
machine is to be worked on, and that power
and utilities will be turned off.
3. Check to make certain no one is operating
the machine before turning off the power.
4. Turn off the equipment using normal
shutdown procedure.
5. Disconnect the energy sources:
a.
Air and hydraulic lines should be bled,
drained and cleaned out. There should
be no pressure in these lines or in the
reservoir tanks. Lockout or tag lines or
valves.
b.
Any mechanism under tension or pres-
sure, such as springs, should be
released and locked out or tagged.
c.
Block any load or machine part prior to
working under it.
d.
Electrical circuits should be checked with
calibrated electrical testing equipment
and stored energy and electrical capaci-
tors should be safely discharged.
6. Lockout and/or Tagout each energy source
using the proper energy isolating devices
and tags. Place lockout hasp and padlock or
tag at the point of power disconnect where
lockout is required by each person
performing work. Each person shall be
provided with their own padlock and have
possession of the only key. If more than one
person is working on a machine
each
person
shall
affix personal lock and tag using a
multi-lock device.
7. Tagout devices shall be used only when
power sources are not capable of being
locked out by use of padlocks and lockout
hasp devices. The name of the person
affixing tag to power source must be on tag
along with date tag was placed on power
source.
8. Release stored energy and bring the
equipment to a “zero mechanical state”.
9. Verify Isolation: Before work is started, test
equipment to ensure power is disconnected.
B.
General Security
1. The lock shall be removed by the
“Authorized” person who put the lock on the
energy-isolating device. No one other than
the person/persons placing padlocks and
lockout hasps on power shall remove
padlock and lockout hasps and restore
power. However, when the authorized
person who applied the lock is unavailable to
remove it his/her Supervisor may remove
padlock/padlocks and lockout hasps and
restore power only if it is first:
a.
verified that no person will be exposed to
danger.
b.
verified that the “Authorized” person who
applied the device is not in the facility.
c.
noted that all reasonable efforts to con-
tact the “Authorized” person have been
made to inform him or her that the lock-
out or tagout device has been removed.
d.
ensured that the “Authorized” person is
notified of lock removal before returning
to work.
2. Tagout System—Tags are warning devices
affixed at points of power disconnect and are
not to be removed by anyone other that the
person placing tag on power lockout. Tags
shall never be by-passed, ignored, or
otherwise defeated
1.13 CALIFORNIA
PROPOSITION 65
WARNING
CALIFORNIA PROPOSITION 65 WARNING
Diesel engine exhaust and some of its con-
stituents are known to the State of Califor-
nia to cause cancer, birth defects and other
reproductive harm.
Battery posts, terminals and related acces-
sories contain lead and other compounds
known to the State of California to cause
cancer and birth defects and other repro-
ductive harm. Wash hands after handling.
Summary of Contents for 02250175-949 R01
