Section 6
NOISE CONTROL
37
6.1 NOISE EMISSIONS WARRANTY
Sullair Corporation warrants to the ultimate pur-
chaser and each subsequent purchaser that this air
compressor was designed, built and equipped to
conform at the time of sale to the first retail pur-
chaser, with all applicable U.S. E.P.A. and/or any
Federal, State or Local noise control regulations.
This warranty is not limited to any particular part,
component, or system of the air compressor. De-
fects in the design, assembly, or in any part, compo-
nent, or system of the compressor which, at the time
of sale to the first retail purchaser, caused noise
emissions to exceed Federal standards are covered
by this warranty for the life of the air compressor.
6.2 TAMPERING WITH THE NOISE CONTROL SYS-
TEM IS PROHIBITED
Federal Law prohibits the following acts or the caus-
ing thereof:
1. The removal or rendering inoperative by any per-
sons, other than for purposes of maintenance,
repair, or replacement, of any device or element
of design incorporated into any new compressor
for the purpose of noise control prior to its sale or
delivery to the ultimate purchaser or while it is in
use.
2. The use of the compressor after such device or
element of design has been removed or ren-
dered inoperative by any person.
Among those acts included in the prohibition
against tampering are the acts listed below:
1. Removal or rendering inoperative any of the fol-
lowing:
a. Engine exhaust system or parts thereof
b. Compressor air intake system or part thereof
c. Enclosure of part thereof
2. Removal of any of the following:
a. Vibration isolators
b. Control silencer
c. Floor panel
d. Fan shroud
e. Acoustical materials including fiberglass foam
or foam tape
3. Operation with canopy doors open for any pur-
pose other than starting, stopping, adjustment,
repair, replacement of parts or maintenance.
6.3 NOISE EMISSIONS MAINTENANCE AND MAIN-
TENANCE RECORD LOG
The following instructions and maintenance record
log book, for the proper maintenance, use and re-
pair of this compressor, is intended to prevent noise
emission degradation (refer to Figure 6---1).
Figure 6---1 Noise Emission Maintenance and Maintenance Record Log
1. ANNUAL MUFFLER AND EXHAUST SYSTEM INSPECTION
At least annually inspect muffler(s) and engine exhaust system to make sure all parts are securely mounted,
that all joints and connections are tight, and that the muffler is in good condition.
DO NOT
operate compres-
sor with defective exhaust system. Remove and replace any defective parts by ordering with part numbers
indicated in the Parts List.
Maintenance
Performed
By
Location
Date
Maintenance
Performed
By
Location
Date
DDDDDDDDDDDDDDDDD
Summary of Contents for 185H
