background image

4

4-2 Installation angle

The installation angle shall be less than the limits shown in Fig.2.

4-1) Location of installation

Ambient temperature

: 0     to +40

(+32     to +104

Ambient humidity

: 85% max.

Ambient atmosphere

: There shall be no corrosive gas, explosive gas.

The installation space shall be well ventilated, and free from dust.

Location of installation : Indoors or outdoors.

. Special specifications are necessary when installation conditions are other than those mentioned here. 

In such cases contact the nearest agent, dealer or service office.

. When a product is made according to special specifications for outdoor use or use in explosive

environments, the product can be safely operated under those specified conditions without problem.

Fig.2 Limits for installation angle

Table1  Torque of the installation bolts

Unit

SPA060

SPA070

SPA080

Bolt Size

M30

M36

Torque

N

m

1400

2430

Size

in

・lbs

12390

21510

. Install PARAMAX SINGLE STAGE DRIVE SPA Series on a sufficiently rigid base.
. Use installation bolts corresponding to JIS strength class 8.8 or its equivalent. The torque of installation bolts is

shown in table1.

5. Coupling with other machines

CAUTION

   Install appropriate guard devices around rotating parts ; otherwise, injury may result.
   When coupling PARAMAX SINGLE STAGE DRIVE SPA Series with a load, confirm that the alignment error is 

within  the specified limits shown in the maintenance manual, drawings, catalog, etc. ; otherwise, damage to 
the system may result, due to misalignment.

   Correctly tighten respective bolts to the specified torque shown in the drawing, catalog, etc. ; otherwise ;

scattering fragments may damage the system.

   Remove the key temporarily attached to the output shaft of PARAMAX SINGLE STAGE DRIVE SPA Series when 

the shaft is free-rotating (i. e. not loaded) ; otherwise, injury may result.

IF a backstop is installed in the reducer, verify that the applied motor rotation direction is correct.
Difference in the direction of rotation may cause injury or damage to the system.

C

C

F)

+1

°

0

+0.3

°

Summary of Contents for PARAMAX SPA Series















Reviews: