background image

 
Assembly Completion Checklist 

 
1. 

Check  and  ensure  that  no  raised  grain  or  splinters  are  evident  on  timber  components. 

Sand down any raised grain or splinters using fine grade sandpaper.

 

 

2.  Check that all screw, nail and pin heads are properly tapped home and are not proud of 
the timber surface. 
 

3. 

Check and ensure that no screws, nails or pins protrude through any panel.

 

 

4.  Check and ensure that all parts are properly secured against reasonable force. 
 

5. 

Do not apply decorative wood finish/treatments to wet or damp timber. Please observe 

the instructions of the wood finish/treatment manufacturer.

 

 

Treatment/care of your Garden Building 

 
Treat  with  a  suitable  decorative  wood  finish  immediately.  We  recommend  that  all  timber 
pieces  be  treated  again  prior  to  assembly  and  again  within  3  months  of  assembly.  We 
further recommend that all pieces are treated again at least annually or as frequently as the 
instructions  on  the  product  used  recommends.  We  would  suggest  that  all  wall  panels  be 
treated  in  an  upside-down  position  to  allow  the  finish/treatment  to  ingress  into  the  tongue 
and groove jointing. We would also remind you that you would rarely (if ever) be able to re-
treat  the  underside  of  the  floor  following  assembly.  We  strongly  recommend  that  the 
underside of the floor is treated an absolute minimum of twice (not including pre-treatment). 
 
Pressure treated buildings come to you already in a light green colour. Whilst your pressure 
treated  building  will  give  you  an  extended  life  compared  to  non-pressure  treated  it  is  still 
beneficial to apply your own choice of good quality long life preservative or stain - although it 
is not absolutely necessary. Any area of timber that you cut, nail or screw after the building 
arrives  to  you  should  be  re-treated  or  stained  to  ensure  an  extended  life.  The  light  green 
colouration can be stained over in your own preferred choice of colour should you wish. 
 
Wood is a natural product and is therefore prone to changes in appearance, including some 
warping, movement and splitting, particularly during unusual climatic conditions (long hot or 
wet spells of weather). As a natural occurrence this is not covered by a guarantee. 
 
Summer Garden Buildings does not guarantee that this is the most recent version of these 
instructions or that all data has been accurately reproduced. You are advised to refer to the 
instructions supplied with the product before assembly. If for any reason the instructions are 
not  delivered  with  the  product  you  are  advised  to  obtain  the  most  recent  version  before 
assembly. No guarantee is given regarding the accuracy of these instructions and no liability 
will be accepted for any errors or inaccuracies. 

 
 
 
 
 
 
 

 

 

Our Help Line provides support and advice to customers of Summer Garden 

Buildings after ordering. For advice before you buy you can phone us free 7 days a 

week on 0800 9777828 or visit www.summergardenbuildings.co.uk 

Summary of Contents for 085













Reviews: