background image

 SUMPSAVER.COM | 605.449.4121

Owner’s Manual- Page 6

OWNER’S MANUAL

All persons operating or using the Sump Saver shall:

1. 

Review.

  Read the following material prior to each use:

 

a. 

This manual;

 

b. 

The Terms and Conditions of Sale;

 

c. 

The supplemental Terms and Conditions available are at 

  

http://sumpsaver.com/terms

 which shall amend this manual; and

 

d. 

The Frequently Asked Questions available at:  

  

http://sumpsaver.com/faqs/.

2. 

Empty Bin Inspections.

  Prior to depositing any grain in any grain bin with  

 

Sump Saver, Purchaser shall: 

 

a. 

Inspect the Sump Saver device to ensure there are no cracks, leaks, or  

 

 

damage to the unit or any of the supporting hoses;

 

b. 

Following a visual inspection, Purchaser shall charge the hydraulic 

 

 

system to ensure the hoses are full of hydraulic fluid and properly 

  connected;

 

c. 

Thereafter, when possible, inspect the Sump Saver, and notify the 

 

 

Manufacturer of any abnormal wear and tear as the interior of a grain  

 

 

bin has high humidity and is a difficult environment.  

3. 

Bi-Annual Inspection.

  Inspect the dust seal on the shaft of the motor at the  

 

beginning and at the end of each crop season.  In the event of any damage 

 

to the  dust seal, Purchaser will contact Sump Saver for maintenance or repair 

 instructions.

4. 

Annual Maintenance. 

 Not less than annually, Purchaser will perform the annual  

 

maintenance inspection and checklist located at 

www.sumpsaver.com

.

5. 

Operation:

 

a. 

No person will enter the grain bin or be in contact with the Sump Saver  

 

 

device while it is connected to any apparatus that applies hydraulic  

  pressure;

 

b. 

Hydraulic pressure to the Sump Saver device shall not exceed 3000 psi.   

 

 

Any pressure exceeding that amount could cause a failure of the device,  

 

 

damage to equipment, loss of hydraulic fluid, or death or injury;

 

c. 

User will not modify the Sump Saver device or make any alterations  

  thereto; 

and

 

d. 

User will not place the arms of Sump Saver next to any solid object or  

 

 

attempt to move any material other than stored grain.

6. WARNINGS:

 

 

MISUSE OR FAILURE TO FOLLOW INSTRUCTIONS IN THE OPERATION OF  

 

SUMP SAVER MAY CAUSE SEVERE INJURY OR DEATH.

 

FAILURE TO CHARGE THE HYDRAULIC HOSES PRIOR TO DEPOSITING   

 

GRAIN IN THE STORAGE BIN MAY RESULT IN CRUSHED HOSES AND AN IN- 

 

OPERABLE SUMP SAVER DEVICE.

Summary of Contents for Mighty Mini











Reviews: