R
IEMPIMENTO
D
El
S
ERBATOIO
D
Ell
’
AcqUA
A
vvERTENZA
:
per evitare il rischio di ustioni, prestare attenzione durate il versamento dell’acqua nel serbatoio del
ferro da stiro caldo. Parti metalliche surriscaldate, acqua calda e vapore possono essere causa di gravi infortuni.
1. Spostare la manopola del valore su
O
/Off (a secco) e il quadrante di selezione tessuti su OFF. Verificare che la
spina del ferro da stiro sia scollegata dalla presa.
2. Sollevare il coperchio del foro di versamento dell’acqua.
3. Riempire il recipiente d’acqua. Versare l’acqua nel serbatoio dell’acqua del ferro da stiro. Non superare il livello di
riempimento massimo.
S
TIRATURA
A
S
EccO
1. Verificare che la manopola del vapore sia impostata su O/Off (a secco).
2. Inserire il cavo nella presa a 220-240V.
3. Ruotare il quadrante di selezione tessuti sull’impostazione desiderata (seta o sintetici). Lasciare riscaldare il ferro
da stiro per 2 minuti. Durante la fase di riscaldamento, verificare che il ferro da stiro sia posto sulla propria base,
su una superficie protetta e stabile.
N
OTA
: quando la manopola del vapore è impostata su
O
/Off (a secco), è possibile utilizzare la funzione GETTO DI
VAPORE o SPRUZZO. Verificare che l’acqua nel serbatoio sia a ¼ di livello.
c
ONSIGlIO
: Per le regolazioni consigliati a fronte dei vari tessuti, fare riferimento alla guida alla stiratura (
a pagina 49
).
S
TIRATURA
A
v
APORE
1. Seguire le istruzioni per il “riempimento del serbatoio dell’acqua”.
2. Inserire il cavo nella presa a 220-240V.
3. Ruotare il quadrante grande di selezione tessuti sull’impostazione desiderata (
sintetici, seta, lino, cotone o lana
).
Lasciare riscaldare il ferro da stiro per 2 minuti. Durante la fase di riscaldamento, verificare che il ferro sia posto
sulla propria base, su una superficie protetta e stabile.
4. Lasciare riscaldare il ferro per 2 minuti, quindi ruotare la manopola del valore sull’impostazione appropriata.
c
ONSIGlIO
: per le regolazioni consigliati a fronte dei vari tessuti, fare riferimento alla guida alla stiratura (
a pagina 49
).
I
MPORTANTE
: Qualora non si debba stirare, spostare la manopola del valore su
O
/Off (a secco) e il quadrante di
selezione tessuti su OFF.
U
TIlIZZO
DEllE
F
UNZIONI
S
PEcIAlI
DEl
F
ERRO
DA
S
TIRO
F
UNZIONE
S
PRUZZO
La funzione di SPRUZZO corrisponde a un potente spruzzo d’acqua che inumidisce il tessuto per semplificare
l’eliminazione delle grinze da tessuti pesati e per fissare le pieghe..
Utilizzo della funzione di SPRUZZO:
Premere a fondo il pulsante SPRAY MIST (SPRUZZO).
F
UNZIONE
G
ETTO
D
I
v
APORE
(solo modelli – 3965-099; IR4500; 4211-099-500; 4211-099-600; 4215-098; 4273-099-500; 4273-099-600)
La funzione GETTO DI VAPORE garantisce un ulteriore fuoriuscita di vapore a garanzia di una maggiore possibilità
d’eliminazione di grinze ostinate. Questa funzione può essere utilizzata sia durante la stiratura a secco, sia a vapore,
ma il serbatoio dell’acqua deve essere colmo almeno per ¼ di livello.
Utilizzo della funzione Getto Di Vapore:
Posizionare il ferro da stiro sulla parte superiore della piega e premere il pulsante SHOT OF STEAM (GETTO
DI VAPORE) ogni qualvolta si desideri la fuoriuscita di più vapore. La funzione GETTO DI VAPORE può essere
utilizzata continuamente, garantendo solamente una breve pausa tra i diversi colpi di vapore.
45