HOW TO USE YOUR HEATING PAD
Make sure Control Connector is securely attached to the Pad Connector
(Figure 1
). Push both parts together for a tight fit.
NOTE:
Control must be connected to heating pad before plugging unit into
outlet.
1. After control is connected to pad, plug into 120V AC electrical outlet.
Your Sunbeam
®
Select-a-Cycle heating pad features a unique
4-in-1 functionality, with 3 preprogrammed settings and the standard
High-Med-Low heat settings.
2. To turn the pad on, press the Power Button. Then select from 3 preprogrammed
settings and 3 standard heat options by scrolling to the desired setting with the
Power button. The LED associated with each setting will illuminate as you scroll through the settings.
3. To turn the pad OFF, press the Power Button until all of the lights are turned off.
WARNINGS:
1. DO NOT SIT ON OR AGAINST OR CRUSH PAD – AVOID FOLDING DURING USE.
2. DO NOT USE WHILE SLEEPING.
3. PLACE PAD ON TOP OF AND NOT UNDER THE PART OF THE BODY NEEDING HEAT.
NOTE: See additional warnings under the SAFEGUARDS section.
PREPROGRAMMED SETTINGS
Rapid: This setting will cycle through 5 minutes on high heat and 8 minutes on medium for 2 hours until Auto
Off activates.
Interval: This setting will cycle through 20 minutes on high heat and 7 minutes on low heat for 2 hours until
Auto Off activates.
Wave: This setting will cycle through 8 minutes on high heat and 20 minutes on low heat for two hours until
Auto Off activates.
For inquiries regarding recycling and proper disposal of this product, please contact your local waste management facility.
www.sunbeam.com
5-YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as
Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of five years from the date of purchase, this product will be free from
defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective
during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any
electrical or mechanical functions on this product. Doing so will void this warranty. This warranty is valid for the original retail purchaser from the
date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance.
JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions
of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the
product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS
or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited
in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be liable for any damages of
any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages
or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party. Some
provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other
rights that vary from province to province, state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
- If you have any question regarding this warranty or would like to obtain warranty service, please call 1-800-435-1250 and a
convenient service center address will be provided to you.
In Canada,
- If you have any question regarding this warranty or would like to obtain warranty service, please call 1-800-667-8623 and a convenient
service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in Boca Raton, Florida
33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, located at 20
B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please write our Consumer
Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
AUTO-OFF FEATURE
Your heating pad controller includes an Auto-Off feature. For each setting, Auto Off will activate after 2 hours
of use.
USING MOIST HEAT THERAPY
In some cases, you may find that moist heat therapy provides more comfort and
relief.
When using moist heat therapy, you should protect furniture and clothing
from becoming damp.
Dampen either side of the heating pad with water by patting the surface with a wet
sponge or cloth or use a spray bottle to apply a fine mist. Do not thoroughly soak pad.
DO NOT SPRAY OR DAMPEN THE PAD CONNECTOR.
(Figure 2)
DANGER: Do not immerse the pad or wiring in water or place under running water.
Failure to comply may result in product failure and/or personal injury.
CAUTION: The electrical pad connector must be thoroughly dry before establishing
electrical connection.
WASHING INSTRUCTIONS
CAUTION: DO NOT DRY CLEAN! DO NOT BLEACH! DO NOT USE WRINGER!
1. Disconnect pad from outlet.
2. Detach Pad Connector from the Control Connector.
3. Wash by hand or as follows in an automatic washer using slow agitation and normal spin speed:
Fill washer with warm water. Add minimum amount of all-purpose detergent, agitate to dissolve,
measure heating pad before washing. Add heating pad and soak five minutes. Agitate two
minutes. Spin. Fill for cool rinse, agitate one minute then spin. Dry in automatic dryer on high
heat, five minutes only, or line dry. Remove damp heating pad from dryer, block to original size,
and drape to finish drying. Do not iron your heating pad.
4. Do not plug in pad and pad connector until they are completely dry.
FCC CERTIFIED
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This product has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This product generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this product does cause harmful interference to radio or television reception,
which can be determined by turning the product off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Figure 2
Figure 1
A. Control Connector
B. Pad Connector
A
B
©2017 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Distributed by Sunbeam Products, Inc. doing business as
Jarden Consumer Solutions, Boca Raton, Florida 33431. Sunbeam Products, Inc. is a subsidiary of Newell Brands Inc. (NYSE: NWL).
Printed in China. DAT100_17EM1 CSH-JC0817-SUN52376 PN: 183061-1
NORTH AMERICAN MODELS WITH POLARIZED PLUGS:
POLARIZED PLUG
THIS APPLIANCE HAS A POLARIZED PLUG, (ONE BLADE
IS WIDER THAN THE OTHER). AS A SAFETY FEATURE
TO REDUCE THE RISK OF ELECTRICAL SHOCK, THIS
PLUG IS INTENDED TO FIT IN A POLARIZED OUTLET
ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET,
REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED
ELECTRICIAN. DO NOT ATTEMPT TO DEFEAT THIS SAFETY FEATURE
OR MODIFY THE PLUG IN ANY WAY. IF THE PLUG FITS LOOSELY INTO
THE AC OUTLET OR IF THE AC OUTLET FEELS WARM DO NOT USE
THAT OUTLET.
ICES CERTIFIED
This product complies with CAN ICES-3 (B)/NMB-3(B).
DAT100_17EM1.indd 2
8/15/17 13:59
