SunBriteTV DS-5518P, Operator'S Manual

SunBriteTV Model 5518HD Operator’s Manual

Page 9

TV Installation – Rear Panel Connections

Connections

1.  SERVICE PORT 

- This port is for factory service only, do not use.

2.  SERVICE PORT

 - This port is for factory service only, do not use.

3.  USB power port

 - 5vdc @ 3.5a Auxillary power supply

4.  1.3mm Power Jack

 - 5vdc @ 3.5a Auxillary power supply

5.  HDMI 1 & 2

 - 

Connects to devices that use HDMI cables such as Blu-ray or HD DVD player or HD cable / satellite set-top box. This connection 

port receives pure digital audio and high definition signal through one single cable. This port also can accept a HDCP video device for video 

or PC for monitor display usage. Use the SOURCE button to select HDMI1 on your MAIN SOURCE to view this connection. Please note: when 

using HDMI, your sound signal must be PCM for the TV to decode digital audio. When using this source for PC display, you must connect the 

audio cable to VGA Stereo Input for audio.

6.  VGA STEREO INPUT - 

This connection port is for people who want to provide audio to the TV when using a PC or a DVI video device. Use a 

3.5mm mini-jack audio cable (headphone jack) to provide audio for a HDCP enabled DVI video device or PCs with VGA or DVI connection.

7.  VGA - 

This connection port connects to a PC for video using VGA cable. Be sure to connect your audio cable to the VGA Stereo input if you 

require sound out of the VGA video source. Use the SOURCE button to select PC on your MAIN SOURCE to view this connection.

8.  COMPONENT 1 (Lower)

 - This connection port is used for DVD players or satellite/cable set-top boxes that use component cables. From left 

to right, connect green, blue and red for video, and then connect white for left channel audio, red for right channel audio. Use the Source 

Button to select Component to view this connection.

9.  COMPONENT 2 (Upper)

 - This connection port is used for DVD players or satellite/cable set-top boxes that use component cables. From left 

to right, connect green, blue and red for video, and then connect white for left channel audio, red for right channel audio. Use the Source 

Button to select Component2 to view this connection.

10.  AV 1

 (CVBS or S-Video) - Connects to devices that use composite or s-video cables such as VCR or camcorder or video game consoles. 

Connect the video portion with either the yellow connector or the S-Video connector. The audio connections are shared between AV1 and 

Svideo. Do NOT connect both video connectors. Use the SOURCE  button to select AV on your MAIN SOURCE if you are using the yellow plug 

for video, use the SOURCE button to select S-Video on your MAIN SOURCE if you are using the S-Video connector to view this connection.

11.  DIGITAL AUDIO OUT(fixed level)

 - This connection port is used for sending out audio signals to other audio devices such as stereo/surround 

sound receivers. The orange (SPDIF OUT) connector sends out either bit-stream or PCM digital sound signal to a home theater receiver with 

digital input.

12.  ATSC/NTSC/QAM Coax input – 

This connection is for digital or analog cable without the cable box or over-the-air antennas. The tuner is a 

hybrid tuner that tunes to both analog and digital channels.  This connection uses coaxial RF cable.  For over-the air digital stations please 

check http://www.antennaweb.org.

13.  IR WINDOW

 - Rear IR receiver, allows IR emitter to be installed inside the cable compartment.

14.  ANALOG AUDIO OUT (Variable) - 

Used to connect headphones, stereo receivers and amplified speakers via a 3.5mm headphone jack.

15.  5 pin din jack

 - SunBriteTV speaker bar connection.

16.  2.5mm power jack 

- 12v @ 3amps Auxillary power supply

17.  RS232 - 

For remote control using RS232 commands.    

1

2

3

7

8

9

11

12

14

10

6

5

4

10

13

15

16 17