Data motor plug:
Technical data:
type
TK3 = 4 pole
voltage rating
230 V
110 V
TK5 = 6 pole
nominal rating abt
30 W
30 W
voltage
230 VAC
rated current
0,13 A
0,26 A
fuse protection
10 A
frequency
50 Hz
60 Hz
system of protection
IP 30
operation mode
S3 50 %
S3 50%
group of isolation
B
direction of rotation
ri + le
ri + l
for dry rooms only
*) test cable type A1 order No. 206 820
test cable type A2 order No. 206 821
No warranty if these instructions are not followed. Subject to technical modifications.
End position installation of assembled sundrape electro drives
Drive runner approximate-
ly in centre of rail. Release
screws in cover lid and
remove them in direction
of arrow. Now you can see
the two buttons for the
end positions.
1. Push safety clip to the
back and press button I
down. Turn button I (both
directions possible) until
all three grooves of index
rings are visible in one line
and switch noise of the microswitch becomes audible.
2. Connect test cable* and switch on for the inactive direction of movement. When the motor starts
going, choose other switching position at the test cable.
ATTENTION!
Setting of the end positions is made with buttons I and II only - Turn button I by hand (both direc-
tions possible) until motor starts running. Hold button I until runners have assembled to a distance
between each other of abt. 10 mm.
Attention: with Corvus blinds it is essential to watch a
safety distance of 10 mm (side of stack).
First end position is set.Turn off operating switch
3. Pull out button I carefully without turning and let it click into place.
4. To set second end position, push safety handle across centre position, press button II. Turn but-
ton II (both directions possible) until all three grooves of index rings are visible in one line and switch
noise of microswitch is heard.
5. Turn on operating switch for opposite running direction. Turn button II by hand (both directions
possible) until motor starts running. Hold button II until first runner has reached a distance of half the
width of a louvre to the end of the blind.
Attention: with Corvus blinds drive onto the snapper
and do not go beyond this position.
Second end position is reached. Switch off operating switch.
6. Pull out carefully button II without turning it and let it engage.
7. Shift safety handle precisely to the middle and fix lid.
8. Test both setting and re-adjust, if necessary.
Attention:
with tandem blinds one motor only is set.
N
= neutral conductor
(neutral blue)
right-handed rotation = control wire
(right brown)
left-handed rotation
= control wire
(left black)
PE
= protective conductor (PE yellow/ green)
Instruction for electrical connection of
sundrape® electric vertical blinds
Before installation of the electric drive, all unne-
cessary wires are to be taken away and existing
installations which are not necessary for a use
with electric supply are to be deactivated. When
mounting electric drives which are operated by
touch contact switch, the touch contact switch
has to be installed near the system, however at a
safety distance to moving parts and above a
height of 1,5 m. For drives delivered without
moving parts, the reference turning moment and
the reference working duration have to be com-
patible with the characteristics of the running
part.. Do not exceed the maximum turning
moment. In case you need more detailed infor-
mation, please contact the manufacturer.
Connections and supply lines to be installed at
the building-site by authorized electro-firms in
compliance with offical regulations. In order to
avoid backing ups of currents in the condensers
of running motors, operate the motors separate-
ly. A separate contact for each rotation direction
of the motors is required (for decoupling purpo-
ses). For controls of more than 2 motors a group
control is required. . Control types for sundrape
electro blinds:
single
in groups with central control
by radio remote control
automatic and central control
Cable laying plans and wiring diagrams are sub-
mitted on request.
3/right-handed rotation
2/left-handed rotation
safety clip
button I
button II
cover
