background image

© 2015 SunEdison 

2

F-SERIES and R-SERIES 

72-Cell Installation Guide

1.0 Introduction

Thank you for choosing SunEdison's Silvantis modules. This 
guide provides information regarding the proper installation 
and handling of Silvantis modules. 

Silvantis modules consist of a series of electrically 
interconnected monocrystalline solar cells that are sealed 
within a laminated sheet of tempered, low glare anti-
reflective coating (ARC) glass superstrate, and EVA back 
sheet substrate. These laminates are secured inside an 
aluminum frame to provide rigidness and a mounting 
mechanism to affix to sub-structures. Do not modify or 
remove frames. 

Please review all the sections that pertain to proper 
installation of modules listed in this guide. The instructions 
detailed in this guide must be followed throughout the 
module’s lifetime deployment. If you need additional 
information about the safe, proper use and handling of 
SunEdison photovoltaic module products, please contact 
SunEdison. 

1.1  Models Covered by Installation Guide

Silvantis Monocrystalline Modules

Silvantis F-Series

F310BzC

F315BzC

F320BzC

F325BzC

F330BzC

F335BzC

Silvantis F-Series U.S. Tariff-Free 

F310BzD

F315BzD

F320BzD

F325BzD

F330BzD

F335BzD

Silvantis R-Series

R330BzC

R335BzC

R340BzC

R345BzC

R350BzC

R355BzC

 z

 indicates manufacturing location: M = Malaysia, X = Mexico, K = Korea 

P = China, T = Taiwan

For product parameters and specifications see Section 7.0.

1.0 Introduction 

2

1.1  Models Covered by Installation Guide  2

2.0  Safety  

3

2.1  General Safety 

3

2.2  Mechanical Safety 

3

2.3  Electrical Safety 

3

3.0  Mechanical Installation  

4

3.1  Planning and Design  

4

3.2  Module Installation Options  

5

3.3  Module Installation Using Center 

Mounting Brackets  

5

3.4  Additional Mounting Methods  

7

4.0  Electrical Installation  

8

4.1  Planning and Design  

8

4.2  Module Wiring 

8

4.3  Grounding  

9

4.3  Option A: Metal Lug 

10

4.3  Option B: Racking Manufacturer 

Integrated Grounding Methods   11

4.3  Option C: Bolt Wire Assembly  11
4.3  Option D: Alternative Grounding  11

5.0 Maintenance 

12

5.1  String Grounding  

12

6.0  Disclaimer of Liability  

13

7.0 Appendix 

14

7.1  Module Details 

14

7.2  Center Clamp Module Installation 

Illustrations 15

7.3  Module Clamp Drawings 

15

Summary of Contents for Silvantis F310BzC

















Reviews: